- 您現在的位置：買賣IC網 > PDF目錄372541 > XAG30 (NXP Semiconductors N.V.) XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs PDF資料下載
參數資料
| 型號： | XAG30 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs |
| 中文描述： | 的XA 16位微控制器系列32K/512檢察官辦公室/光盤/無ROM，看門狗，2個UART |
| 文件頁數： | 15/36頁 |
| 文件大小： | 208K |
| 代理商： | XAG30 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Philips Semiconductors
Product specification
XA-G3
XA 16-bit microcontroller family
32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
1999 Apr 07
15
PRE2
PRE1
PRE0
—
—
WDRUN
WDTOF
WDCON
8–BIT DOWN
COUNTER
PRESCALER
TCLK
MOV WFEED1,#A5H
MOV WFEED2,#5AH
WATCHDOG FEED SEQUENCE
WDL
SU00581A
—
INTERNAL RESET
Figure 10. Watchdog Timer in XA-G3
When the watchdog underflows, the following action takes place
(see Figure 10):
Autoload takes place.
Watchdog time-out flag is set
Watchdog run bit unchanged.
Autoload (WDL) register unchanged.
Prescaler tap unchanged.
All other device action same as external reset.
Note that if the watchdog underflows, the program counter will be
loaded from the reset vector as in the case of an internal reset. The
watchdog time-out flag can be examined to determine if the
watchdog has caused the reset condition. The watchdog time-out
flag bit can be cleared by software.
WDCON Register Bit Definitions
WDCON.7
PRE2
WDCON.6
PRE1
WDCON.5
PRE0
WDCON.4
—
WDCON.3
—
WDCON.2
WDRUN
WDCON.1
WDTOF
WDCON.0
—
Prescaler Select 2, reset to 1
Prescaler Select 1, reset to 1
Prescaler Select 0, reset to 1
Watchdog Run Control bit, reset to 1
Timeout flag
UARTs
The XA-G3 includes 2 UART ports that are compatible with the
enhanced UART used on the 8xC51FB. Baud rate selection is
somewhat different due to the clocking scheme used for the XA
timers.
Some other enhancements have been made to UART operation.
The first is that there are separate interrupt vectors for each UART’s
transmit and receive functions. The UART transmitter has been
double buffered, allowing packed transmission of data with no gaps
between bytes and less critical interrupt service routine timing. A
independently of the UART itself and provides a start-of-break status
bit that the program may test. Finally, an Overrun Error flag has
been added to detect missed characters in the received data
stream. The double buffered UART transmitter may require some
software changes in code written for the original XA-G3 single
buffered UART.
Each UART baud rate is determined by either a fixed division of the
oscillator (in UART modes 0 and 2) or by the timer 1 or timer 2
overflow rate (in UART modes 1 and 3).
Timer 1 defaults to clock both UART0 and UART1. Timer 2 can be
programmed to clock either UART0 through T2CON (via bits R0CLK
and T0CLK) or UART1 through T2MOD (via bits R1CLK and
T1CLK). In this case, the UART not clocked by T2 could use T1 as
the clock source.
The serial port receive and transmit registers are both accessed at
Special Function Register SnBUF. Writing to SnBUF loads the
transmit register, and reading SnBUF accesses a physically
separate receive register.
The serial port can operate in 4 modes:
Mode 0:
Serial I/O expansion mode.
Serial data enters and exits
through RxDn. TxDn outputs the shift clock. 8 bits are
transmitted/received (LSB first). (The baud rate is fixed at 1/16 the
oscillator frequency.)
Mode 1: Standard 8-bit UART mode.
10 bits are transmitted
(through TxDn) or received (through RxDn): a start bit (0), 8 data
bits (LSB first), and a stop bit (1). On receive, the stop bit goes into
RB8 in Special Function Register SnCON. The baud rate is variable.
Mode 2: Fixed rate 9-bit UART mode.
11 bits are transmitted
(through TxD) or received (through RxD): start bit (0), 8 data bits
(LSB first), a programmable 9th data bit, and a stop bit (1). On
Transmit, the 9th data bit (TB8_n in SnCON) can be assigned the
value of 0 or 1. Or, for example, the parity bit (P, in the PSW) could
be moved into TB8_n. On receive, the 9th data bit goes into RB8_n
in Special Function Register SnCON, while the stop bit is ignored.
The baud rate is programmable to 1/32 of the oscillator frequency.
Mode 3: Standard 9-bit UART mode.
11 bits are transmitted
(through TxDn) or received (through RxDn): a start bit (0), 8 data
bits (LSB first), a programmable 9th data bit, and a stop bit (1).
In fact, Mode 3 is the same as Mode 2 in all respects except baud
rate. The baud rate in Mode 3 is variable.
In all four modes, transmission is initiated by any instruction that
uses SnBUF as a destination register. Reception is initiated in
Mode 0 by the condition RI_n = 0 and REN_n = 1. Reception is
initiated in the other modes by the incoming start bit if REN_n = 1.
相關PDF資料 |
PDF描述 |
|---|---|
| XAM1214-130 | RF POWER TRANSISTORS L-BAND RADAR APPLICATIONS |
| XB0ASB03A1BR | SCHOTTKY BARRIER DIODE 500MA 30V TYPE |
| XB15A407 | PIN DIODE |
| XB15A709 | PIN DIODE |
| XC1718 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XA-G30 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family 512 B RAM, watchdog, 2 UARTs |
| XA-G37 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family 32K OTP, 512 B RAM, watchdog, 2 UARTs |
| XA-G39 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family XA 16-bit microcontroller 32K FLASH/1K RAM, watchdog, 2 UARTs |
| XA-G49 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs |
| XAGU-50A | 制造商:Distributed By MCM 功能描述:Agu Fuses 50A, Package of 5 制造商:MCM 功能描述:AGU FUSES 50A 5 PACK |
發布緊急采購，3分鐘左右您將得到回復。