Philips Semiconductors
Preliminary specification
XA-G49
XA 16-bit microcontroller family
64K Flash/2K RAM, watchdog, 2 UARTs
2000 Apr 03
32
ABSOLUTE MAXIMUM RATINGS
PARAMETER
RATING
UNIT
°
C
°
C
V
Operating temperature under bias
–55 to +125
Storage temperature range
–65 to +150
Voltage on EA/V
PP
pin to V
SS
Voltage on any other pin to V
SS
Maximum I
OL
per I/O pin
Power dissipation (based on package heat transfer limitations, not device power consumption)
0 to +13.0
–0.5 to V
DD
+0.5V
15
V
mA
1.5
W
DC ELECTRICAL CHARACTERISTICS
V
DD
= 4.5V to 5.5V unless otherwise specified;
T
amb
= 0 to +70
°
C for commercial, –40
°
C to +85
°
C for industrial, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
UNIT
MIN
TYP
MAX
Supplies
I
DD
I
ID
I
PD
I
PDI
V
RAM
V
IL
V
IH
V
IH1
V
IL1
V
OL
V
OH1
V
OH2
C
IO
I
IL
I
LI
I
TL
NOTES:
1. Ports in Quasi bi-directional mode with weak pull-up (applies to ALE, PSEN only during RESET).
2. Ports in Push-Pull mode, both pull-up and pull-down assumed to be same strength
3. In all output modes
4. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
V
IN
is approximately 2V.
5. Measured with port in high impedance output mode.
6. Measured with port in quasi-bidirectional output mode.
7. Load capacitance for all outputs=80pF.
8. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin:
15mA (*NOTE: This is 85
°
C specification for V
DD
= 5V.)
Maximum I
OL
per 8-bit port:
26mA
Maximum total I
for all output: 71mA
If I
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
Supply current operating
5.5V, 30 MHz
110
mA
Idle mode supply current
5.5V, 30 MHz
40
mA
Power-down current
Power-down current (–40
°
C to +85
°
C)
RAM-keep-alive voltage
30
A
150
A
RAM-keep-alive voltage
1.5
V
Input low voltage
–0.5
0.22V
DD
V
Input high voltage, except XTAL1, RST
At 5.0V
2.2
V
Input high voltage to XTAL1, RST
At 5.0V
0.8V
DD
V
Input low voltage to XATL1, RST
Output low voltage all ports, ALE, PSEN
3
Output high voltage all ports, ALE, PSEN
1
Output high voltage, ports P0–3, ALE, PSEN
2
At 5.0V
0.12V
DD
0.5
I
OL
= 3.2mA, V
DD
= 5.0V
I
OH
= –100 A, V
DD
= 4.5V
I
OH
= 3.2mA, V
DD
= 4.5V
V
2.4
V
2.4
V
Input/Output pin capacitance
Logical 0 input current, P0–3
6
Input leakage current, P0–3
5
Logical 1 to 0 transition current all ports
4
15
pF
V
IN
= 0.45V
V
IN
= V
IL
or V
IH
At 5.5V
–25
–75
±
10
–650
A
A
A