- 您現在的位置：買賣IC網 > PDF目錄1973 > X96010V14IZ (Intersil)IC SENSOR CONDITIONER 14-TSSOP PDF資料下載
參數資料
| 型號： | X96010V14IZ |
| 廠商： | Intersil |
| 文件頁數： | 2/26頁 |
| 文件大小： | 0K |
| 描述： | IC SENSOR CONDITIONER 14-TSSOP |
| 標準包裝： | 95 |
| 類型： | 傳感器調節器 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 接口： | 2 線 |
| 電流 - 電源： | 15mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1246 (CN2011-ZH PDF) |
10
FN8214.1
October 25, 2005
PRINCIPLES OF OPERATION
CONTROL AND STATUS REGISTERS
The Control and Status Registers provide the user
with a mechanism for changing and reading the value
of various parameters of the X96010. The X96010
contains seven Control, one Status, and several
Reserved registers, each being one Byte wide (See
Figure 4). The Control registers 0 through 6 are
located at memory addresses 80h through 86h
respectively. The Status register is at memory address
87h, and the Reserved registers at memory address
88h through 8Fh.
All bits in Control register 6 always power-up to the logic
state “0”. All bits in Control registers 0 through 5 power-
up to the logic state value kept in their corresponding
nonvolatile memory cells. The nonvolatile bits of a reg-
ister retain their stored values even when the X96010 is
powered down, then powered back up. The nonvolatile
bits in Control 0 through Control 5 registers are all pre-
programmed to the logic state “0” at the factory, except
the cases that indicate “1” in Figure 4.
Bits indicated as “Reserved” are ignored when read,
and must be written as “0”, if any Write operation is
performed to their registers.
A detailed description of the function of each of the
Control and Status register bits follows:
Control Register 0
This register is accessed by performing a Read or
Write operation to address 80h of memory.
VRM: VOLTAGE REFERENCE PIN MODE (NON-
VOLATILE
)
The VRM bit configures the Voltage Reference pin
(VRef) as either an input or an output. When the VRM
bit is set to “0” (default), the voltage at pin VRef is an
output from the X96010’s internal voltage reference.
When the VRM bit is set to “1”, the voltage reference
for the VRef pin is external. See Figure 5.
ADCFILTOFF: ADC FILTERING CONTROL (NON-
VOLATILE
)
When this bit is“1”, the status register at 87h is
updated after every conversion of the ADC. When this
bit is “0” (default), the status register is updated after
four consecutive conversions with the same result, on
the 6 MSBs.
NV1234: CONTROL REGISTERS 1, 2, 3, AND 4 VOLA-
TILITY MODE SELECTION BIT
(NON-VOLATILE)
When the NV1234 bit is set to “0” (default), bytes writ-
ten to Control registers 1, 2, 3, and 4 are stored in vol-
atile cells, and their content is lost when the X96010 is
powered down. When the NV1234 bit is set to “1”,
bytes written to Control registers 1, 2, 3, and 4 are
stored in both volatile and nonvolatile cells, and their
value doesn’t change when the X96010 is powered
down and powered back up. See “Writing to Control
I1DS: CURRENT GENERATOR 1 DIRECTION SELECT BIT
(NON-VOLATILE)
The I1DS bit sets the polarity of Current Generator 1,
DAC1. When this bit is set to “0” (default), the Current
Generator 1 of the X96010 is configured as a Current
Source. Current Generator 1 is configured as a Cur-
rent Sink when the I1DS bit is set to “1”. See Figure 7.
X96010
相關PDF資料 |
PDF描述 |
|---|---|
| X96012V14IZT1 | IC BIAS CTRLR UNIV SNSR 14-TSSOP |
| X9C303V8T2 | IC XDCP 100-TAP 32K EE 8-TSSOP |
| X9C503ST2 | IC XDCP 100-TAP 50K EE 8-SOIC |
| XA2C128-8CPG132Q | IC CPLD 128MC 100 I/O 132CSBGA |
| XA2C32A-7VQG44Q | IC CPLD 32MCELL 33 I/O 44-VQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X96011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Sensor with Look-Up Table Memory and DAC |
| X96011_08 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Sensor with Look-Up Table Memory and DAC |
| X96011V14I | 功能描述:CONDITIONER SGNL W/TABLE MEM&DAC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| X96011V14IZ | 功能描述:IC SENSOR TEMP BIAS SGL 14-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| X96012 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Universal Sensor Conditioner with Dual Look-up Table Memory and DACs |
發布緊急采購，3分鐘左右您將得到回復。