- 您現在的位置：買賣IC網 > PDF目錄372540 > X9521 Dual DCP, EEPROM Memory PDF資料下載
參數資料
| 型號： | X9521 |
| 英文描述： | Dual DCP, EEPROM Memory |
| 中文描述： | 雙二氯酚，EEPROM存儲器 |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 434K |
| 代理商： | X9521 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
REV 1.1.9 1/30/03
Characteristics subject to change without notice.
3 of 26
www.xicor.com
X9521
– Preliminary Information
PRINCIPLES OF OPERATION
SERIAL INTERFACE
Serial Interface Conventions
The device supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter, and the receiving device as the
receiver. The device controlling the transfer is called the
master and the device being controlled is called the slave.
The master always initiates data transfers, and provides
the clock for both transmit and receive operations. There-
fore, the X9521 operates as a slave in all applications.
Serial Clock and Data
Data states on the SDA line can change only while SCL is
LOW. SDA state changes while SCL is HIGH are
reserved for indicating START and STOP conditions. See
Figure 1. On power up of the X9521, the SDA pin is in the
input mode.
Serial Start Condition
All commands are preceded by the START condition,
which is a HIGH to LOW transition of SDA while SCL is
HIGH. The device continuously monitors the SDA and
SCL lines for the START condition and does not respond
to any command until this condition has been met. See
Figure 2.
Serial Stop Condition
All communications must be terminated by a STOP condi-
tion, which is a LOW to HIGH transition of SDA while SCL
is HIGH. The STOP condition is also used to place the
device into the Standby power mode after a read
sequence. A STOP condition can only be issued after the
transmitting device has released the bus. See Figure 2.
Serial Acknowledge
An ACKNOWLEDGE (ACK) is a software convention
used to indicate a successful data transfer. The transmit-
ting device, either master or slave, will release the bus
after transmitting eight bits. During the ninth clock cycle,
the receiver will pull the SDA line LOW to ACKNOWL-
EDGE that it received the eight bits of data. Refer to Fig-
ure 3.
The device will respond with an ACKNOWLEDGE after
recognition of a START condition if the correct Device
Identifier bits are contained in the Slave Address Byte. If a
write operation is selected, the device will respond with an
ACKNOWLEDGE after the receipt of each subsequent
eight bit word.
In the read mode, the device will transmit eight bits of
data, release the SDA line, then monitor the line for an
ACKNOWLEDGE. If an ACKNOWLEDGE is detected
and no STOP condition is generated by the master, the
device will continue to transmit data. The device will termi-
SCL
SDA
Data Stable
Data Change
Data Stable
Figure 1.
Valid Data Changes on the SDA Bus
SCL
SDA
Start
Stop
Figure 2.
Valid Start and Stop Conditions
相關PDF資料 |
PDF描述 |
|---|---|
| X9521 | Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules |
| X9521V20I | Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules |
| X95820 | Dual Digitally Controlled Potentiometers (XDCP)(雙數控電位器) |
| X95840 | Quad Digital Controlled Potentiometers (XDCP)(四數控電位器（XDCP）) |
| x96012(中文) | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9521_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20I | 功能描述:IC LASR CTRLR 2CHAN 5.5V 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9521V20I-A | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9521V20I-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20IZ-A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
發布緊急采購，3分鐘左右您將得到回復。