- 您現在的位置：買賣IC網 > PDF目錄376445 > X9111TV14Z-2.7 (INTERSIL CORP) Single Digitally-Controlled (XDCP⑩) Potentiometer PDF資料下載
參數資料
| 型號： | X9111TV14Z-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Single Digitally-Controlled (XDCP⑩) Potentiometer |
| 中文描述： | 100K DIGITAL POTENTIOMETER, 3-WIRE SERIAL CONTROL INTERFACE, 1024 POSITIONS, PDSO14 |
| 封裝： | 4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-14 |
| 文件頁數： | 3/17頁 |
| 文件大?。?/td> | 323K |
| 代理商： | X9111TV14Z-2.7 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
3
FN8159.4
September 15, 2006
Pin Descriptions
Bus Interface Pins
SERIAL OUTPUT (SO)
SO is a serial data output pin. During a read cycle, data is
shifted out on this pin. Data is clocked out by the falling edge
of the serial clock.
SERIAL INPUT (SI)
SI is the serial data input pin. All opcodes, byte addresses and
data to be written to the pots and pot registers are input on this
pin. Data is latched by the rising edge of the serial clock.
SERIAL CLOCK (SCK)
The SCK input is used to clock data into and out of the
X9111.
HOLD (HOLD)
HOLD is used in conjunction with the CS pin to select the
device. Once the part is selected and a serial sequence is
underway, HOLD may be used to pause the serial
communication with the controller without resetting the serial
sequence. To pause, HOLD must be brought LOW while SCK is
LOW. To resume communication, HOLD is brought HIGH, again
while SCK is LOW. If the pause feature is not used, HOLD should
be held HIGH at all times.
DEVICE ADDRESS (A
0
, A
1
)
The address inputs are used to set the 8-bit slave address. A
match in the slave address serial data stream must be made
with the address input (A1–A0) in order to initiate
communication with the X9111.
CHIP SELECT (CS)
When CS is HIGH, the X9111 is deselected and the SO pin is at
high impedance, and (unless an internal write cycle is
underway) the device will be in the standby state. CS LOW
enables the X9111, placing it in the active power mode. It
should be noted that after a power-up, a HIGH to LOW
transition on CS is required prior to the start of any operation.
HARDWARE WRITE PROTECT INPUT (WP)
The WP pin when LOW prevents nonvolatile writes to the
Data Registers.
Potentiometer Pins
R
H
, R
L
The R
H
and R
L
pins are equivalent to the terminal connections
on a mechanical potentiometer.
R
W
The wiper pin is equivalent to the wiper terminal of a
mechanical potentiometer.
Bias Supply Pins
SYSTEM SUPPLY VOLTAGE (V
CC
) AND SUPPLY
GROUND (V
SS
)
The V
CC
pin is the system supply voltage. The V
SS
pin is
the system ground.
Other Pins
NO CONNECT (NC)
Pin should be left open. This pin is used for Intersil
manufacturing and test purposes.
Principles of Operation
Device Description
Serial Interface
The X9111 supports the SPI interface hardware conventions.
The device is accessed via the SI input with data clocked-in on
the rising SCK. CS must be LOW and the HOLD and WP pins
must be HIGH during the entire operation.
The SO and SI pins can be connected together, since they
have three state outputs. This can help to reduce system pin
count.
Array Description
The X9111 is comprised of a resistor array (see Figure 1).
The array contains the equivalent of 1023 discrete resistive
segments that are connected in series. The physical ends of
each array are equivalent to the fixed terminals of a
mechanical potentiometer (R
H
and R
L
inputs).
At both ends of each array and between each resistor
segment is a CMOS switch connected to the wiper (R
W
)
output. Within the individual array only one switch may be
turned on at a time.
Pin Descriptions
PIN
(TSSOP)
SYMBOL
FUNCTION
1
SO
Serial Data Output
2
A0
Device Address
3
NC
No Connect
4
CS
Chip Select
5
SCK
Serial Clock
6
SI
Serial Data Input
7
V
SS
System Ground
8
WP
Hardware Write Protect
9
A1
Device Address
10
HOLD
Device Select. Pause the Serial Bus
11
R
W
Wiper Terminal of the Potentiometer
12
R
H
High Terminal of the Potentiometer
13
R
L
Low Terminal of the Potentiometer
14
V
CC
System Supply Voltage
X9111
相關PDF資料 |
PDF描述 |
|---|---|
| X9116WM8T1 | Digitally Controlled Potentiometer |
| X9116WM8ZT1 | Digitally Controlled Potentiometer |
| X9118 | Dual Suply/Low Power/1024-Tap/2-Wire Bus |
| X9118-2.7 | Dual Suply/Low Power/1024-Tap/2-Wire Bus |
| X9118TV14 | Dual Suply/Low Power/1024-Tap/2-Wire Bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9116 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116_11 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Digitally Controlled Potentiometer |
| X9116WM8 | 功能描述:IC DIGITAL POT 10K 16TP 8MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
| X9116WM8-2.7 | 功能描述:IC XDCP 16-TAP 10K CMOS 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:2,500 系列:XDCP™ 接片:256 電阻（歐姆）:100k 電路數:1 溫度系數:標準值 ±300 ppm/°C 存儲器類型:非易失 接口:I²C（設備位址） 電源電壓:2.7 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。