- 您現在的位置：買賣IC網 > PDF目錄372534 > X5165 RTC Module With CPU Supervisor PDF資料下載
參數資料
| 型號： | X5165 |
| 元件分類： | CPU監測 |
| 英文描述： | RTC Module With CPU Supervisor |
| 中文描述： | 時鐘模塊CPU監控 |
| 文件頁數： | 5/21頁 |
| 文件大?。?/td> | 365K |
| 代理商： | X5165 |
5
FN8128.3
June 1, 2006
Principles Of Operation
Power-on Reset
Application of power to the X5163, X5165 activates a Power-
on Reset Circuit. This circuit goes active at 1V and pulls the
RESET/RESET pin active. This signal prevents the system
microprocessor from starting to operate with insufficient
voltage or prior to stabilization of the oscillator. When V
CC
exceeds the device V
TRIP
value for 200ms (nominal) the
circuit releases RESET/RESET, allowing the processor to
begin executing code.
Low Voltage Monitoring
During operation, the X5163, X5165 monitors the V
CC
level
and asserts RESET/RESET if supply voltage falls below a
preset minimum V
TRIP
. The RESET/RESET signal prevents
the microprocessor from operating in a power fail or
brownout condition. The RESET/RESET signal remains
active until the voltage drops below 1V. It also remains active
until V
CC
returns and exceeds V
TRIP
for 200ms.
Watchdog Timer
The Watchdog Timer circuit monitors the microprocessor
activity by monitoring the WDI input. The microprocessor
must toggle the CS/WDI pin periodically to prevent a
RESET/RESET signal. The CS/WDI pin must be toggled
from HIGH to LOW prior to the expiration of the watchdog
time out period. The state of two nonvolatile control bits in
the Status Register determine the watchdog timer period.
The microprocessor can change these watchdog bits, or
they may be “l(fā)ocked” by tying the WP pin LOW and setting
the WPEN bit HIGH.
V
CC
Threshold Reset Procedure
The X5163, X5165 has a standard V
CC
threshold (V
TRIP
)
voltage. This value will not change over normal operating
and storage conditions. However, in applications where the
standard V
TRIP
is not exactly right, or for higher precision in
the V
TRIP
value, the X5163, X5165 threshold may be
adjusted.
Setting the V
TRIP
Voltage
This procedure sets the V
TRIP
to a higher voltage value. For
example, if the current V
TRIP
is 4.4V and the new V
TRIP
is
4.6V, this procedure directly makes the change. If the new
setting is lower than the current setting, then it is necessary
to reset the trip point before setting the new value.
To set the new V
TRIP
voltage, apply the desired V
TRIP
threshold to the V
CC
pin and tie the CS/WDI pin and the WP
pin HIGH. RESET and SO pins are left unconnected. Then
apply the programming voltage V
P
to both SCK and SI and
pulse CS/WDI LOW then HIGH. Remove V
P
and the
sequence is complete.
Resetting the V
TRIP
Voltage
This procedure sets the V
TRIP
to a “native” voltage level. For
example, if the current V
TRIP
is 4.4V and the V
TRIP
is reset,
the new V
TRIP
is something less than 1.7V. This procedure
must be used to set the voltage to a lower value.
To reset the V
TRIP
voltage, apply a voltage between 2.7 and
5.5V to the V
CC
pin. Tie the CS/WDI pin, the WP pin, AND
THE SCK pin HIGH. RESET and SO pins are left
unconnected. Then apply the programming voltage V
P
to the
SI pin ONLY and pulse CS/WDI LOW then HIGH. Remove V
P
and the sequence is complete.
SCK
SI
V
P
V
P
CS
FIGURE 1. SET V
TRIP
VOLTAGE
SCK
SI
V
CC
V
P
CS
FIGURE 2. RESET V
TRIP
VOLTAGE
X5163, X5165
相關PDF資料 |
PDF描述 |
|---|---|
| X5168 | RTC Module With CPU Supervisor |
| X5169 | RTC Module With CPU Supervisor |
| X5323(中文) | RTC Module With CPU Supervisor |
| X5323 | RTC Module With CPU Supervisor |
| X5325 | RTC Module With CPU Supervisor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X5165P | 功能描述:IC CPU SUPRV 16K EE RST HI 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| X5165P-2.7 | 功能描述:IC SUPERVISOR CPU 16K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5165P-2.7A | 功能描述:IC SUPERVISOR CPU 16K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5165P-4.5A | 功能描述:IC SUPERVISOR CPU 16K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
| X5165PI | 功能描述:IC SUPERVISOR CPU 16K EE 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:推挽式，圖騰柱 復位:低有效 復位超時:最小 145 ms 電壓 - 閥值:2.64V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WQFN 裸露焊盤 供應商設備封裝:16-TQFN-EP（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。