- 您現在的位置：買賣IC網 > PDF目錄245702 > W78M64VP110SBC (MICROSEMI CORP-PMG MICROELECTRONICS) SPECIALTY MEMORY CIRCUIT, PBGA156 PDF資料下載
參數資料
| 型號： | W78M64VP110SBC |
| 廠商： | MICROSEMI CORP-PMG MICROELECTRONICS |
| 元件分類： | 存儲器 |
| 英文描述： | SPECIALTY MEMORY CIRCUIT, PBGA156 |
| 封裝： | 13 X 22 MM, PLASTIC, BGA-156 |
| 文件頁數： | 22/48頁 |
| 文件大?。?/td> | 1548K |
| 代理商： | W78M64VP110SBC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
29
White Electronic Designs Corporation (602) 437-1520 www.whiteedc.com
White Electronic Designs
W78M64VP-XSBX
October 2008
Rev. 2
ADVANCED
White Electronic Designs Corp. reserves the right to change products or specications without notice.
TABLE 38 MEMORY ARRAY COMMAND DEFINITIONS
Command
Cycles
Bus Cycles (Note 1-5)
First
Second
Third
Fouth
Fifth
Sixth
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
Read (6)
1
RA
RD
Reset (7)
1
XXX
F0
AutoSelect
(8,
9)
Manufacturer ID
4
555
AA
2AA
55
555
90
X00
01
Device ID (8)
4
555
AA
2AA
55
555
90
X01
227E
X0E
(8)
X0F
(8)
Sector Protect Verify (10)
4
555
AA
2AA
55
555
90
[SA]X02
(10)
Secure Device Verify (11)
4
555
AA
2AA
55
555
90
X03
(11)
CFI Query (12)
1
55
98
Program
4
555
AA
2AA
55
555
A0
PA
PD
Write to Buffer
3
555
AA
2AA
55
SA
25
SA
WC
WBL
PD
WBL
PD
Program Buffer to Flash (Conrm)
1
SA
29
Write-to-Buffer-Abort Reset
3
555
AA
2AA
55
555
F0
Unlock
Bypass
Enter
3
555
AA
2AA
55
555
20
Program (14)
2
XXX
A0
PA
PD
Sector Erase (14)
2
XXX
80
SA
30
Chip Erase (14)
2
XXX
80
XXX
10
Reset (15)
2
XXX
90
XXX
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Erase Suspend/Program Suspend (16)
1
XXX
B0
Erase Resume/Program Resume (17)
1
XXX
30
Secured Silicon Sector Entry
3
555
AA
2AA
55
555
88
Secured SIlicon Sector Exit (18)
4
555
AA
2AA
55
555
90
XX
00
Legend
X = Don’t care
RA = Address of the memory to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling
edge of the WE# or CE# pulse, whichever happens later.
Notes
1.
See Table 7.1 for description of bus operations.
2.
All values are in hexadecimal.
3.
All bus cycles are write cycles unless otherwise noted.
4.
Data bits DQ15-DQ8 are don’t cares for unlock and command cycles.
5.
Address bits AMAX:A16 are don’t cares for unlock and command cycles, unless SA
or PA required. (AMAX is the Highest Address pin.).
6.
No unlock or command cycles required when reading array data.
7.
The Reset command is required to return to reading array data when device is in the
autoselect mode, or if DQ5 goes high (while the device is providing status data).
8.
See Table 7.2 for device ID values and denitions.
9.
The fourth, fth, and sixth cycles of the autoselect command sequence are read
cycles.
10. The data is 00h for an unprotected sector and 01h for a protected sector. See
Autoselect for more information. This is same as PPB Status Read except that the
protect and unprotect statuses are inverted here.
11. The data value for DQ7 is “1” for a serialized, protected Secured Silicon Sector region
and “0” for an unserialized, unprotected region. See data and denitions.
PD = Data to be programmed at location PA. Data latches on the rising edge of the WE# or
CE# pulse, whichever happens rst.
SA = Address of the sector to be veried (in autoselect mode) or erased. Address bits
Amax–A16 uniquely select any sector.
WBL = Write Buffer Location. The address must be within the same write buffer page as
PA.
WC = Word Count is the number of write buffer locations to load minus 1.
12. Command is valid when device is ready to read array data or when device is in
autoselect mode.
13. Command sequence returns device to reading array after being placed in a Write-to-
Buffer-Abort state. Full command sequence is required if resetting out of abort while
in Unlock Bypass mode.
14. The Unlock-Bypass command is required prior to the Unlock-Bypass- Program
command.
15. The Unlock-Bypass-Reset command is required to return to reading array data when
the device is in the unlock bypass mode.
16. The system can read and program/program suspend in non-erasing sectors, or
enter the autoselect mode, when in the Erase Suspend mode. The Erase Suspend
command is valid only during a sector erase operation.
17. The Erase Resume/Program Resume command is valid only during the Erase
Suspend/Program Suspend modes.
18. The Exit command returns the device to reading the array.
相關PDF資料 |
PDF描述 |
|---|---|
| W7NCF512H11CS6BG | 32M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| W7NCF512H11IS9CG | 32M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
| WE128K32-150G2Q | 128K X 32 EEPROM 5V MODULE, 150 ns, CQFP68 |
| WE32K32-80G2TI | 32K X 32 EEPROM 5V MODULE, 80 ns, CQMA68 |
| WF2M32I-150G2UI5 | 2M X 32 FLASH 5V PROM MODULE, 150 ns, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78M64VP110SBM | 制造商:Microsemi Corporation 功能描述:8MX64 FLASH 3.3V PAGE MODE - Bulk |
| W78M64V-XSBX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flash MCP |
| W78NCSX-23 | 功能描述:低信號繼電器 - PCB 4PDT 3A 24VDC IND RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| W78PCX-1 | 制造商:Magnecraft 功能描述: |
| W78PCX-2 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。