參數資料
型號: W78ERD2A40PN
廠商: WINBOND ELECTRONICS CORP
元件分類: 微控制器/微處理器
英文描述: 8-BIT MICROCONTROLLER
中文描述: 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44
封裝: PLASTIC, LCC-44
文件頁數: 8/72頁
文件大?。?/td> 606K
代理商: W78ERD2A40PN
W78ERD2
- 8 -
6.3 Clock
The W78ERD2 is designed with either a crystal oscillator or an external clock.
6.4 Crystal Oscillator
The W78ERD2 incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be
connected across pins XTAL1 and XTAL2. In addition, a load capacitor must be connected from each
pin to ground, and a resistor must also be connected from XTAL1 to XTAL2 to provide a DC bias
when the crystal frequency is above 24 MHz.
6.5 External Clock
An external clock should be connected to pin XTAL1. Pin XTAL2 should be left unconnected. The
XTAL1 input is a CMOS-type input, as required by the crystal oscillator. As a result, the external clock
signal should have an input one level of greater than 3.5 volts.
6.6 Power Management
6.6.1 Idle Mode
Setting the IDL bit in the PCON register enters the idle mode. In the idle mode, the internal clock to the
processor is stopped. The peripherals and the interrupt logic continue to be clocked. The processor
will exit idle mode when either an interrupt or a reset occurs.
6.6.2
Power-down Mode
When the PD bit in the PCON register is set, the processor enters the power-down mode. In this mode
all of the clocks are stopped, including the oscillator. To exit from power-down mode is by a hardware
reset or external interrupts INT0 to INT1 when enabled and set to level triggered.
6.7 Reduce EMI Emission
If the crystal frequency is under 25 MHz, please option.b7 is set to 0 by the writer. Please refer option
bits description to operate this bit.
6.8 Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running. An internal trigger circuit in the reset line is used to
deglitch the reset line when the W78ERD2 is used with an external RC network. The reset logic also
has a special glitch removal circuit that ignores glitches on the reset line. During reset, the ports are
initialized to FFH, the stack pointer to 07H, PCON (with the exception of bit 4) to 00H, and all of the
other SFR registers except SBUF to 00H. SBUF is not reset.
相關PDF資料
PDF描述
W78IE52 8 BIT MICROCONTROLLER
W78IE54 8-BIT MTP Monitor Microcontroller(多次可編程的8位的監視微控制器)
W78IE54P 8-BIT MTP MICROCONTROLLER
W78IRD2 8-BIT MICROCONTROLLER
W78IRD2A 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
W78I052A 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W78I052A24DL 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W78I052A24PL 功能描述:IC MCU 8-BIT 8K FLASH 40-DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:W78 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI,I²C,LIN,SPI,UART/USART 外圍設備:電容感應,DMA,LCD,POR,PWM,WDT 輸入/輸出數:25 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b,D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
W78I052DDG 功能描述:IC MCU 8-BIT 8K FLASH 40-DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:W78 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO,I²C,LIN,UART/USART 外圍設備:DMA,LVD,POR,PWM,WDT 輸入/輸出數:27 程序存儲器容量:16KB(16K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤
W78I052DFG 功能描述:IC MCU 8-BIT 8K FLASH 44-PQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:W78 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO,I²C,LIN,UART/USART 外圍設備:DMA,LVD,POR,PWM,WDT 輸入/輸出數:27 程序存儲器容量:16KB(16K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤