參數資料
型號： W78E378
廠商： WINBOND ELECTRONICS CORP
元件分類： 微控制器/微處理器
英文描述： MONITOR MICROCONTROLLER
中文描述： 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PDIP32
封裝： 0.600 INCH, PLASTIC, DIP-32
文件頁數： 20/38頁
文件大小： 396K
代理商： W78E378
Preliminary W78E378/W78C378/W78C374
- 20 -
Bit Freq. (KHz) @Fosc
8 MHz
CR2
CR1
CR0
10 MHz
Fosc Divided
By
256
224
192
160
960
120
60
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
31.25
35.7
41.7
50.0
8.3
66.7
133.3
39.1
44.6
52.1
62.5
10.4
83.3
166.7
a-4) The Status Register, S1STA
S1STA is an 8-bit read-only register. The three least significant bits are always 0. The five most
significant bits contain the status code. There are 23 possible status codes. When S1STA contains
F8H
, no serial interrupt is requested. All other S1STA values correspond to defined SIO1 states.
When each of these states is entered, a status interrupt is requested (SI = 1). A valid status code is
present in S1STA one machine cycle after SI is set by hardware and is still present one machine
cycle after SI has been reset by software.
In addition, state
00H
stands for a Bus Error. A Bus Error occurs when a START or STOP condition is
present at an illegal position in the format frame. Examples of illegal positions are during the serial
transfer of an address byte, a data byte or an acknowledge bit.
b) Operating Modes
The four operating modes are: Master/Transmitter, Master/Receiver, Slave/Transmitter and
Slave/Receiver. Bits STA, STO and AA in S1CON decide the next action the SIO1 hardware will take
after SI is cleared. When the next action is completed, a new status code in S1STA will be updated
and SI will be set by hardware in the same time. Now, the interrupt service routine is entered (if the
SI_interrupt is enabled), the new status code can be used to decide which appropriate service routine
the software is to branch. Data transfers in each mode are shown in the following figures.
*** Legend for the following four figures:
(STA,STO,SI,AA)=(0,0,0,X)
SLA+W will be transmitted;
ACK bit will be received.
SLA+W has been transmitted;
ACK has been received.
18H
08H
A START has been
transmitted.
Last action is done
Last state
Next setting in S1CON
Expected next action
New state
Next action is done
1) "Data byte will be transmitted":
Software should load the data byte (to be transmitted) into S1DAT
before new S1CON setting is done.
2) "SLA+W (R) will be transmitted":
Software should load the SLA+W/R (to be transmitted) into S1DAT
before new S1CON setting is done.
3) "Data byte will be received":
Software can read the received data byte from S1DAT
while a new state is entered.
Software's access to S1DAT with respect to "Expected next action":
相關PDF資料
PDF描述
W78E378P MONITOR MICROCONTROLLER
W78C438B 8-BIT Microcontroller(8位的微控制器)
W78C438C40FL 8-BIT MICROCONTROLLER
W78C438C40PL 8-BIT MICROCONTROLLER
W78C458 8-BIT EMULATION MICROCONTROLLER
相關代理商/技術參數
參數描述
W78E378A10PL 功能描述:IC MCU 8-BIT 32K FLASH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W78 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO，I²C，LIN，UART/USART 外圍設備:DMA，LVD，POR，PWM，WDT 輸入/輸出數:27 程序存儲器容量:16KB（16K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤
W78E378P 制造商:WINBOND 制造商全稱:Winbond 功能描述:MONITOR MICROCONTROLLER
W78E51-16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
W78E51-24 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
W78E51-33 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*