- 您現在的位置：買賣IC網 > PDF目錄231492 > W19B320STB9F (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 PDF資料下載
參數資料
| 型號： | W19B320STB9F |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| 封裝： | TFBGA-48 |
| 文件頁數： | 3/52頁 |
| 文件大?。?/td> | 1869K |
| 代理商： | W19B320STB9F |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
W19B(L)320ST/B
Publication Release Date: March 23, 2004
- 11 -
Revision A2
6.2.1 Reading Array Data
After device power-up, it is automatically set to reading array data. There is no commands are
required to retrieve data. After completing an Embedded Program or Embedded Erase algorithm, the
device is ready to read array data.
After the device accepts an Erase Suspend command, it enters the erase-suspend-read mode. After
this the system can read data from any non-erase-suspended sector. And then, after completing a
programming operation in the Erase Suspend mode, the system may once again read array data with
the same exception. Please refer to Erase Suspend/Erase Resume Commands section for detail
information.
The system must initiate the reset command to return the device to read (or erase-suspend-read)
mode if DQ5 goes high during an active program or erase operation; otherwise, the device is in the
autoselect mode. See Reset Command section and Requirements for Reading Array Data in the
Device Bus Operations section for more information.
6.2.2 Reset Command
The device will be to the read or erase-suspend-read mode when writing the reset command. For this
command, the address bits are Don’t Care.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to which the system was writing to the read mode. Once
erasure begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence
before programming begins. This resets the device, to which the system was writing to the read mode.
If the program command sequence is written to the device, in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode. When programming begins, the
device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command
sequence. When in the autoselect mode, the reset command must be written to return to the read
mode. If the device entered into the autoselect mode while in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the device
to the read mode (or erase-suspend-read mode if the device was in Erase Suspend).
6.2.3 Autoselect Command Sequence
The autoselect command sequence provides the host system to access the manufacturer and device
codes, and determine whether a sector is protected or not. This is an alternative method, which is
intended for PROM programmers and requires VID on address pin A9. The autoselect command
sequence may be written to an address within the device that is either in the read or erase-suspend-
read mode. When the device is actively programming or erasing, the autoselect command may not be
written.
The first writing two unlock cycles initiate the autoselect command sequence. This is followed by a
third write cycle that contains the autoselect command. The device then enters into the autoselect
mode. The system may read at any address without initiating another autoselect command sequence:
A read cycle at address XX00h returns the manufacturer code.
A read cycle at address XX01h in word mode(or XX02h in byte mode) returns the device code.
相關PDF資料 |
PDF描述 |
|---|---|
| WED3DG7266V7D1I-MG | 64M X 72 SYNCHRONOUS DRAM MODULE, ZMA144 |
| WEDPN16M64V-133B2M | 16M X 64 SYNCHRONOUS DRAM, 5.5 ns, PBGA219 |
| W25X32-VSSI-Z | 32M X 1 FLASH 2.7V PROM, PDSO8 |
| WF1024K32E-150H2M | 4M X 8 FLASH 12V PROM MODULE, 150 ns, CHIP66 |
| WS128K48-20G4WMA | 768K X 8 MULTI DEVICE SRAM MODULE, 20 ns, CQFP116 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W19L-E02050 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E03040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19L-E04040 | 制造商:Cooper Crouse-Hinds 功能描述: |
| W19U_5LGA WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| W1A | 功能描述:ENCLOSURE 7.25X4.5 GREY RoHS:是 類別:盒，外殼，支架 >> 箱 系列:工具 產品目錄繪圖:SR Series Standard 特色產品:Customize Your Enclosure 標準包裝:1 系列:S 容器 - 類型:盒 尺寸/尺寸:3.600" L x 2.250" W（91.44mm x 57.15mm） 高度:1.500"（38.10mm） 面積 (L x W):8.10"（52.3cm） 設計:手持，分叉式雙側 材質:塑料 - ABS 顏色:杏黃 厚度:0.100"（2.54mm） 特點:PCB 支座 額定值:IP40，NEMA 1 材料可燃性額定值:UL94 HB 裝運信息:從 Digi-Key 運送 重量:0.137 磅（62.14g） 相關產品:SR6005-ND - SCREW NO.4X 3/8 H/L PANSRPS-11-ND - GASKET 3.63 X 2.27 INCHSR52-ND - BOX RUBBER FEET FOR "A" SERIESSR410-ND - PC BOARD COPPER CLADSR310-ND - PC BOARD .1" STD HORIZ GRIDSR50-ND - RUBBER FEET (1XX,2XX) 其它名稱:111-I ALMOND111-IA111-IALMONDSR111-IA |
發布緊急采購，3分鐘左右您將得到回復。