- 您現在的位置：買賣IC網 > PDF目錄359454 > W172DIP-147 RELAY REED DIL 5VDC PDF資料下載
參數資料
| 型號： | W172DIP-147 |
| 英文描述： | RELAY REED DIL 5VDC |
| 中文描述： | 勵迪勒5Vdc時繼電器 |
| 文件頁數： | 68/210頁 |
| 文件大?。?/td> | 7067K |
| 代理商： | W172DIP-147 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁當前第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁
APPLICATION DATA
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
12345
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
MERCURY-WETTED CONTACT RELAYS. ( CONTINUED)
Mercury wetted contacts are fast in operation and have relatively good load
carrying capacity and long life. The mercury films are reestablished at each
contact closure and contact erosion is eliminated.. The mercury films are
stretchable, there is no contact bounce and because it is a mercury contact, the
contact resistance is very low and ideal for low level switching applications.
The disadvantages of this type of reed relay are the freezing point of mercury
(-38C), poor resistance to shock and vibration and the need to mount the relay in
a near vertical position.
These relays are used for a variety of switching applications such as found in
computers, business machines, machine tool control systems, and laboratory
instruments.
CONTACT COMBINATIONS.
The switches used in dry reed relays provide SPST-NO, SPST-NC, SPDT contact
combinations.
The SPST-NO corresponds with the basic switch capsule design (Fig.1).
The SPST-NC results from a combination of the SPST-NO switch and
a permanent magnet strong enough to pull the contacts closed but able to open
when coil voltage is applied to the relay coil.
In typical true SPDT designs, the armature is mechanically tensioned
against the normally closed contact, and is moved to the normally open contact
upon application of a magnetic field. The SPDT contact combination can also be
achieved by joining a SPST-NO switch with an appropriately adjusted SPST-NC
switch, and jumping one side of both switches together to form the movable contact
system.
Latching contacts, defined as contacts which remain in the position to
which they were driven, and staying in that position when coil power is removed
from the relay coil.
Latching switches are manufactured by using a SPST-NO contact, and biasing it
with a permanent magnetic that is strong enough to hold the contacts closed,
but not strong enough to hold the contact closed when coil power is applied to the
coil. The switching process is than reversed by simply reversing the relay coil
polarity to close the switch.
MAGNETIC FIELDS
Reed relays in general can be characterized as susceptible to the influences of
external magnetic fields. It is important to keep reed relays at a proper distance
from each other because of the possibility of magnetic-interaction between them.
Proper magnetic shielding must be used to contain stray magnetic fields. When
installing reed relays into equipment, one should be aware of the devices within
that equipment which can produce magnetic fields. The relays being installed into
that equipment should be positioned as far away as possible from any stray
magnetic fields and should be shielded to prevent false operations.
ELECTRICAL CHARACTERISTICS
SENSITIVITY: The input power required to operate dry reed relays is determined
by the sensitivity of the particular reed switch used, by the number of switches
operated by the coil, by the permanent magnet biasing (if used), and the efficiency
of the coil and the effectiveness of its coupling to the blades. Minimum input
required to effect closure ranges from the very low milliwatt level for a single
sensitive capsule to several watts for multipole relays.
OPERATE TIME: The coil time constant, overdrive on the coil, and the character-
istics of the reed switch determine operate time. With the maximum overdrive
voltage applied to the coil, reed relays will operate in approximately the 200
microsecond range. When driven at rated coil voltage, usually the relays will
operate at about one millisecond.
RELEASE TIME: With the coil unsuppressed, dry reed switch contacts release
in a fraction of a millisecond. SPST-NO contacts will open in as little as 50
microseconds. Magnetically biased SPST-NC and SPDT switches reclose from
100 microseconds to 1 millisecond respectively.
UP
OPERATING
POSITION
Mercury
pool
Glass
Capsule
Movable
contact blade
Supporting
Leadwire
Figure 2. Miniature Mercury-wetted contact switch (SPDT)
REED
RELAYS
PAGE 68
WEBSITE: www.magnecraft.com EMAIL:info@magnecraft.com FAX ON DEMAND 1-800/891-2957, DOCUMENT 100
HOW REED RELAYS WORK
The term reed relay covers dry reed relays and mercury-wetted
contact relays, all of which use hermetically sealed reed switches.
In both types, the reeds (thin, flat blades) serve multiple functions -
as conductor, contacts, springs, and magnetic armatures.
DRY REED RELAYS
Dry reed relays have become an important factor in the relay field.
They have the advantage of being hermetically sealed and resistant
to atmospheric contamination. They have fast operate and release
times and when operated within their rated contact loads, have very
long life. A typical dry reed switch capsule is shown in Figure 1.
Open
Contacts
1231234567890123456789012123456
1231234567890123456789012123456
1231234567890123456789012123456
1231234567890123456789012123456
1231234567890123456789012123456
Capsule
Supporting
Terminal
Supporting
Terminal
Figure 1.
Construction of Switch Capsule of Typical Dry Reed switch (SPST-NO)
In the basic SPST-NO design, two opposing blades are sealed into a
narrow glass capsule and overlapped at their free ends. The contact
area is plated typically with rhodium to produce a low contact resistance
when contacts are drawn together. The capsule is made of glass and
filled with a dry inert gas and then sealed. The capsule is surrounded by
an electromagnetic coil. When the coil is energized, the normally open
contacts are brought together; when the coil voltage is removed, the
blades separate by their own spring tension. Some reeds contain
permanent magnets for magnetic biasing to achieve normally closed
contacts (SPST-NC) or SPDT contact combinations. The current rating,
which is dependent upon the size of the blade and the type and amount
of plating, may range from low level to 1 amp. Effective contact protection
is essential when switching loads other then dry resistive loads.
MERCURY-WETTED CONTACT RELAYS.
Mercury wetted contacts consist of a glass-encapsulated reed with its
base immersed in a pool of mercury and the other end capable of moving
between one or two stationary contacts. The mercury flows up the reed by
capillary action and wets the contact surfaces of the moving end of the
reed as well as the contact surfaces of the stationary contacts. A mercury
to mercury contact is maintained in the closed position. The capsule is
surrounded by an electromagnetic coil and operates in the same manner
as a dry reed.
相關PDF資料 |
PDF描述 |
|---|---|
| W172DIP-149 | RELAY REED DIL 12VDC |
| W389ACX-10 | INDUSTRIERELAIS FLANSCH 230AC |
| W388CQX-7 | INDUSTRIERELAIS FLANSCH 24VDC |
| W388ACQX-10 | INDUSTRIERELAIS FLANSCH 230V |
| W171DIP-10 | RELAY REED DIL 24VDC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W172DIP-149 | 功能描述:簧片繼電器 172DIP Mini Reed PCB Relay / SPDT, 0.25 A RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| W172DIP-150 | 功能描述:簧片繼電器 172DIP Mini Reed PCB Relay / SPDT, 0.25 A RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| W172DIP-163 | 制造商:Magnecraft 功能描述: |
| W172DIP-17 | 功能描述:簧片繼電器 172DIP Mini Reed PCB Relay / DPDT, 0.25 A RoHS:否 制造商:MEDER electronic (Standex) 觸點形式:1 Form A (SPST-NO) 線圈電壓:5 VDC 最大開關功率:100 W 最大開關電流:1 A 線圈抑制二極管:No 線圈電阻:220 Ohms 端接類型: |
| W172DIP-18 | 制造商:Magnecraft 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。