
W137
5
Absolute Maximum Ratings
Stresses greater than those listed in this table may cause per-
manent damage to the device. These represent a stress rating
only. Operation of the device at these or any other conditions
above those specified in the operating sections of this specifi-
cation is not implied. Maximum conditions for extended peri-
ods may affect reliability.
.
Parameter
V
DD
, V
IN
T
STG
T
A
T
B
ESD
PROT
Description
Rating
–0.5 to +7.0
–65 to +150
0 to +70
–55 to +125
2 (min.)
Unit
V
°C
°C
°C
kV
Voltage on any pin with respect to GND
Storage Temperature
Operating Temperature
Ambient Temperature under Bias
Input ESD Protection
DC Electrical Characteristics:
T
A
= 0°C to +70°C; V
DDQ3
= 3.3V±5%; V
DDQ2
= 2.5V±5%; CPU0:1 = 66.6/100 MHz
Parameter
Description
Supply Current
I
DD3PD
3.3V Supply Current in Power-down mode
I
DD3
3.3V Supply Current
I
DD2
2.5V Supply Current
I
DD2PD
2.5V Supply Current in Power-down mode
Logic Inputs
V
IL
Input Low Voltage
V
IH
Input High Voltage
I
IL
I
IH
I
IL
Input Low Current (SEL100/66#)
I
IH
Input High Current (SEL100/66#)
Clock Outputs
V
OL
Output Low Voltage
V
OH
Output High Voltage
Test Condition
Min.
Typ.
Max.
Unit
PWR_DWN# = 0
Outputs Loaded
[1]
Outputs Loaded
[1]
PWR_DWN# = 0
1
5
mA
mA
mA
mA
80
30
100
45
1
0.2 μA
GND – 0.3
2.0
0.8
V
V
μA
μA
μA
μA
V
DD
+ 0.3
–25
10
–5
+5
Input Low Current
[2]
Input High Current
[2]
I
OL
= 1 mA
I
OH
= –1 mA
50
mV
V
PCI_F, PCI1:5,
REF0:1
CPU0:1
CPU0:1
PCI_F, PCI1:5
REF0:1
CPU0:1
PCI_F, PCI1:5
REF0:1
3.1
V
OH
I
OL
Output High Voltage
Output Low Current:
I
OH
= –1 mA
V
OL
= 1.25V
V
OL
= 1.5V
V
OL
= 1.5V
V
OH
= 1.25V
V
OH
= 1.5V
V
OH
= 1.5V
2.2
80
70
50
80
70
50
V
120
110
70
120
110
70
180
140
90
180
140
90
mA
mA
mA
mA
mA
mA
I
OH
Output High Current
Crystal Oscillator
V
TH
C
LOAD
C
IN,X1
Notes:
1.
All clock outputs loaded with 6" 60
transmission lines with 20-pF capacitors.
2.
CPU_STOP#, PCI_STOP#, PWR_DWN#, SPREAD#, and SEL48# logic inputs have internal pull-up resistors (not CMOS level).
3.
X1 input threshold voltage (typical) is V
/2.
4.
The W137 contains an internal crystal load capacitor between pin X1 and ground and another between pin X2 and ground. Total load placed on crystal is
14 pF; this includes typical stray capacitance of short PCB traces to crystal.
5.
X1 input capacitance is applicable when driving X1 with an external clock source (X2 is left unconnected).
X1 Input Threshold Voltage
[3]
Load Capacitance, As Seen by External Crystal
[4]
X1 Input Capacitance
[5]
VDDQ3 = 3.3V
1.65
14
28
V
pF
pF
Pin X2 unconnected