- 您現在的位置：買賣IC網 > PDF目錄361748 > VSP3100 14-Bit, 10MHz CCD/CIS SIGNAL PROCESSOR PDF資料下載
參數資料
| 型號： | VSP3100 |
| 英文描述： | 14-Bit, 10MHz CCD/CIS SIGNAL PROCESSOR |
| 中文描述： | 14位，10MHz的防治荒漠化公約/ CIS信號處理器 |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 195K |
| 代理商： | VSP3100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁
16
VSP3100
These registers can be accessed by the following two pro-
gramming modes:
(1) Parallel Programming Mode using digital data output
pins, with the data bus assigned as D0 to D9 (pins 25 to 34),
and the address bus as A0 to A2 (pins 35 to 37). It can be
used for both reading and writing operations. However, it
cannot be used by the Demultiplexed mode (when D7 of the
Configuration Register is set to “1”).
(2) Serial Programming Mode using a serial port, Serial Data
(SD), the Serial Shift Clock (SCLK), and Write Signal
(WRT) assigned.
It can be used only for writing operations; reading opera-
tions via the serial port are prohibited.
Table III shows how to access these modes.
Power-on default value is all “0s”, set to 3-channel CCD
mode with 1V internal reference, R > G > B MUX sequence,
and normal output mode.
For reading/writing to the Configuration Register, the ad-
dress will be A2 = “0”, A1 =“0”, and A0 = “0”.
For Example:
A 3-channel CCD with internal reference V
REF
= 1V (2V
full-scale input), R > G > B sequence and normal output
mode will be D0 = “0”, D1 = “0”, D2 =“0”, D3 = “0”,
D4 = “x (don’t care)”, D5 = “x (don’t care)”, D6 = “0”, and
D7 = “0”.
For this example, bypass V
REF
with an appropriate capacitor
(for example, 10
μ
F to 0.1
μ
F) when internal reference mode
is used.
Another Example:
A 1-channel CIS mode (Green channel) with an external
1.2V reference (2.4V full-scale input), Demultiplexed Out-
put mode will be D0 = “1”, D1 = “x (don’t care)”, D2 = “1”,
D3 = “1”, D4 = “0”, D5 = “1”, D6 = “x (don’t care)”, and
D7 = “1”.
For this example, V
REF
will be an input pin applied with
1.2V.
OFFSET REGISTER
Offset Registers control the analog offset input to channels
prior to the PGA. There is a 10-bit Offset Register on each
channel. The offset range varies from –400mV to +400mV.
The Offset Register uses a straight binary code. All “0s”
corresponds to –400mV, and all “1s” corresponds to +400mV
of the offset adjustment. The register code 200
H
corresponds
to 0mV of the offset adjustment. The Power-on default value
of the Offset Register is all ”0s”, so the offset adjustment
should be set to –400mV.
PGA GAIN REGISTER
PGA Gain Registers control the gain to channels prior to the
digitization by the A/D converter. There is a 5-bit PGA Gain
Register on each channel. The gain range varies from 1 to
4.44 (from 0dB to 13dB). The PGA Gain Register is a
straight binary code. All “0s” corresponds to an analog gain
of 0dB, and all “1s” corresponds to an analog gain of 13dB.
PGA Transfer function is log gain curve. Power-on default
value is all “0s”, so that it sets the gain of 0dB.
BIT
LOGIC ‘0’
LOGIC ‘1’
D0
D1
D2
D3
CCD mode
V
REF
= 1V
Internal Reference
3-channel Mode,
D4 and D5 disabled
D4,D5 (disabled when 3-channel)
CIS mode
V
REF
=1.5V
External Reference
1-channel Mode,
D4 and D5 enabled
D4 D5
0
0
1-channel mode, Red channel
0
1
1-channel mode, Green channel
1
0
1-channel mode, Blue channel
MUX Sequence
Blue > Green >Red
Demultiplexed output mode
D6
MUX Sequence
Red > Green > Blue
Normal output mode
D7
TABLE IV. Configuration Register Design.
OE
P/S
MODE
0
0
1
1
0
1
0
1
Digital data output enabled, Serial mode enabled
Prohibit mode
Digital data output disabled, Serial mode enabled
Digital data output disabled, Parallel mode enabled
TABLE III. Access Mode for Serial and Parallel Port.
CONFIGURATION REGISTER
The Configuration Register design is shown in Table IV.
相關PDF資料 |
PDF描述 |
|---|---|
| VSP3100Y | 14-Bit, 10MHz CCD/CIS SIGNAL PROCESSOR |
| VSP3200 | CCD SIGNAL PROCESSOR FOR SCANNER APPLICATIONS |
| VSP3200Y | CCD SIGNAL PROCESSOR FOR SCANNER APPLICATIONS |
| VSP3210 | CCD SIGNAL PROCESSOR FOR SCANNER APPLICATIONS |
| VSP3210Y | CCD SIGNAL PROCESSOR FOR SCANNER APPLICATIONS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VSP3100Y | 功能描述:視頻模擬/數字化轉換器集成電路 14-Bit 10Msps CCD/ CIS Signal Processor RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| VSP3100Y/2K | 功能描述:視頻模擬/數字化轉換器集成電路 14-Bit 10Msps CCD/ CIS Signal Processor RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| VSP3100Y/2KG4 | 功能描述:視頻模擬/數字化轉換器集成電路 14-Bit 10Msps CCD/ CIS Signal Processor RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| VSP3100YG4 | 功能描述:視頻模擬/數字化轉換器集成電路 14-Bit 10Msps CCD/ CIS Signal Processor RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| VSP3200 | 制造商:BB 制造商全稱:BB 功能描述:CCD SIGNAL PROCESSOR FOR SCANNER APPLICATIONS |
發布緊急采購，3分鐘左右您將得到回復。