- 您現在的位置：買賣IC網 > PDF目錄359408 > VP-1608F (Electronic Theatre Controls, Inc.) Digital Voice Processor PDF資料下載
參數資料
| 型號： | VP-1608F |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Digital Voice Processor |
| 中文描述： | 數字語音處理器 |
| 文件頁數： | 5/7頁 |
| 文件大小： | 966K |
| 代理商： | VP-1608F |
VP-1608..........................................................................................5
VOICE
ENV2:
Envelop input for channel B, to be connected to INT2 with
a feedback resistor.
INT1:
Integrator output for channel A, to be connected to an
external RC integration circuitry.
INT2:
Integrator output for channel B, to be connected to an
external RC integration circuitry.
I/O1:
Strobe input/Busy output for channel A, active low. To
play a message on channel A, place the segment/bank
code on INA to INE and strobe this pin with a low pulse.
During the playback this pin becomes an active-low "busy"
output. If this pin is held low at the end of playback, the
message will be re-triggered.
I/O2:
Same as I/O1 except that this pin is for channel B.
INA ~ IND:
Input for segment code in binary format. INA is the LSB
and IND is the MSB.
INE, INF:
Input for bank code in binary format, max. 4 banks. INE is
the LSB and INF is the MSB.
OSC1, OSC2:
Internal oscillator pins for external RC components. It
external clock source is to be used, feed it through the
OSC2 pin. Note that both channels share the same clock,
so their sampling rate must be the same.
RESET1:
Reset input for channel A, active low. On the falling edge
of this reset signal, channel A playback is stopped and all
internal counters for channel A are cleared.
RESET2:
Reset input for channel B, active low. On the falling edge
of this reset signal, channel B playback is stopped and all
internal counters for channel B are cleared.
SCK, TEST:
For factory use only, do not make any connection.
SE, SF:
Output for EPROM bank select. These two pins are actually
latched outputs for INE and INF.
VDD:
Input, supply voltage.
VDS & VAS:
VDS is digital ground and VAS is analog ground. Connect
the two grounds together close to the power source to
minimize noise.
APPLICATION NOTES
1. EOM (End Of Message) Flag
The EOM flag consists of six consecutive bytes of "AA", or
"10101010" in binary format. After a trigger signal is
received, the VP-1608 uses the internal 8MHz system clock
to scan through memory space and finds the correct
message by counting the number of EOM flags. For
example, to find the 5th message, it must scan through
each and every memory location until it finds 4 EOM flags.
The first byte following the 4th EOM flag is the first byte
of the 5th message.
2. Creating Master EPROM File on the VP-880 System
Follow these steps to create the master EPROM file:
1. To maximize the EPROM usage, arrange your sound
segments in banks of 16 or less, so that the total combined
length for each bank is about the same. Do not mix
channel A and channel B together.
2. Based on the total combined length of the largest bank,
select a highest sampling rate that will fully utilize the
EPROM. Use the following equation:
Sampling Rate (Kbps) =
EPROM Size (K-bits) / Total Length (Second)
3. Digitize and edit each segment as a separate file. Use
the "ROM Data Management" function to combine up to
16 messages into a "bank file". The first filename entered
in the "ROM Data Management" is the first segment in that
bank, and etc.
4. Depending on the hardware design, each EPROM chip
may contain one or more sound banks. It is also possible
to use just one EPROM to store all sound segments of both
channel A and channel B. If you need to combine several
bank files into one for programming into one EPROM chip,
use the following DOS command:
COPY /b file_1+file_2+..+file_n destination_file
Do not use the "ROM Data Management" function to
combine bank files, otherwise each bank file will be
considered as a single message file.
相關PDF資料 |
PDF描述 |
|---|---|
| VP0104 | P-Channel Enhancement-Mode Vertical DMOS FET(擊穿電壓-40V,8Ω，P溝道增強型垂直DMOS結構場效應管) |
| VP0106 | P-Channel Enhancement-Mode Vertical DMOS FETs |
| VP0106N3 | P-Channel Enhancement-Mode Vertical DMOS FETs |
| VP0120N3 | TRANSISTOR | MOSFET | P-CHANNEL | 200V V(BR)DSS | 100MA I(D) | TO-92 |
| VP0120 | P-Channel Enhancement-Mode Vertical DMOS FETs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| VP160-B1Z9Z-00000 | 制造商:Carling Technologies 功能描述:V-SERIES ILLUMINATED PLUG - Bulk |
| VP160-B1ZEZ-00000 | 制造商:Carling Technologies 功能描述:V-SERIES ILLUMINATED PLUG - Bulk |
| VP160-B1ZEZ-CS100 | 制造商:Carling Technologies 功能描述:V-SERIES ILLUMINATED PLUG - Bulk |
| VP160-B1ZEZ-CS1XX-XPT1 | 制造商:Carling Technologies 功能描述:V-SERIES ILLUMINATED PLUG - Bulk |
| VP160-B1ZEZ-DV100 | 制造商:Carling Technologies 功能描述:V-SERIES ILLUMINATED PLUG - Bulk |
發布緊急采購，3分鐘左右您將得到回復。