- 您現在的位置：買賣IC網 > PDF目錄361611 > V048F015T090 (Vicor Corporation) VI Chip - VTM Voltage Transformation Module PDF資料下載
參數資料
| 型號： | V048F015T090 |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | VI Chip - VTM Voltage Transformation Module |
| 中文描述： | 六芯片- VTM電壓轉換模塊 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 497K |
| 代理商： | V048F015T090 |
Vicor Corporation
Tel: 800-735-6200
vicorpower.com
VI Chip Voltage Transformation Module
V048K015T090
Rev. 1.0 Page 10 of 16
PRELIMINARY
Configuration Options (Cont.)
Figure 17
—VTM test circuit
F1
Temperature Monitor
Load
+
–
7 A
Fuse
C1
100
μ
F
Al electrolytic
+
–
Input reflected ripple
measurement point
C2
ceramic
μ
F
+
14 V
-In
PC
VC
TM
+In
-Out
+Out
VTM
+Out
-Out
K
Ro
Application Note
Parallel Operation
In applications requiring higher current or redundancy, VTMs
can be operated in parallel without adding control circuitry or
signal lines. To maximize current sharing accuracy, it is imperative
that the source and load impedance on each VTM in a parallel
array be equal. If VTMs are being fed by an upstream PRM, the
VC nodes of all VTMs must be connectd to the PRM VC.
To achieve matched impedances, dedicated power planes
within the PC board should be used for the output and output
return paths to the array of paralleled VTMs. This technique is
preferable to using traces of varying size and length.
The VTM power train and control architecture allow bi-directional
power transfer when the VTM is operating within its specified
ranges. Bi-directional power processing improves transient
response in the event of an output load dump. The VTM may
operate in reverse, returning output power back to the input
source. It does so efficiently.
Thermal Management
The high efficiency of the VTM results in low power
dissipation minimizing temperature rise, even at full output
current. The heat generated within the internal semiconductor
junctions is coupled through very low thermal resistances, R
θ
JC
and R
θ
JB
(see Figure 18), to the PC board allowing flexible
thermal management.
CASE 1 Convection via optional Pin Fins to air (Pin Fins
available as a separate item.)
In an environment with forced convection over the surface
of a PCB with 0.4" of headroom, a VTM with Pin Fins offers
a simple thermal management option. The total Junction to
Ambient thermal resistance of a surface mounted
V048K015T090 with pin fins attached is 4.8 oC/W in 300 LFM
airflow, (see Figure 19).
At 1.5 Vout and full rated current (90A), the VTM dissipates
approximately 13 W per Figure 4. This results in a temperature
rise of approximately 60 oC, allowing operation in an air
temperature of 65 oC without exceeding the 125 oC max
junction temperature.
CASE 2 Conduction to the PC board
The low Junction to BGAthermal resistance allows the use
of the PC board as a means of removing heat from the VTM.
Convection from the PC board to ambient, or conduction to a
cold plate, enable flexible thermal management options.
With a VTM mounted on a 2.0 in
2
area of a multi-layer PC
board with appropriate power planes resulting in 8 oz of
effective copper weight, the Junction-to-BGAthermal
resistance, R
θ
JB
, is 2.1 oC/W in 300 LFM of air. With a
maximum junction temperature of 125 oC and 13 W of
dissipation at full current of 90 A, the resulting temperature
rise of 26 oC allows the VTM to operate at full rated current
up to a 99 oC board temperature. See thermal resistances
on page 9 for additional details on this thermal management
option.
Adding low-profile heat sinks to the PC board can lower the
thermal resistance of the PC board surrounding the VTM.
Additional cooling may be added by coupling a cold plate to
the PC board with low thermal resistance stand offs.
CASE 3 Combined direct convection to the air and conduction
to the PC board.
Acombination of cooling techniques that utilize the power
planes and dissipation to the air will also reduce the total
thermal impedance. This is the most effective cooling
method. To estimate the total effect of the combination, treat
each cooling branch as one leg of a parallel resistor network.
Notes:
C3 should be placed close to the load
C3
200 μF
15 m
相關PDF資料 |
PDF描述 |
|---|---|
| V048A015T090 | VI Chip - VTM Voltage Transformation Module |
| V048F015T100 | VI Chip - PRM-AL Pre-Regulator Module |
| V048F015T80 | VI Chip - VTM Voltage Transformation Module |
| V048F030T070 | VI Chip - VTM Voltage Transformation Module |
| V048K030T070 | VI Chip - VTM Voltage Transformation Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V048F015T100 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:VI Chip - VTM Voltage Transformation Module |
| V048F015T80 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:VI Chip - VTM Voltage Transformation Module |
| V048F020M006 | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY |
| V048F020M009 | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY |
| V048F020M012 | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:300W DC/DC VOLTAGE TRANSFORMATION MODULE PRELIMINARY |
發布緊急采購，3分鐘左右您將得到回復。