參數資料
型號: uPSD3234BV-40U6T
廠商: 意法半導體
英文描述: Flash Programmable System Devices with 8032 Microcontroller Core
中文描述: 閃存可編程系統設備與8032微控制器內核
文件頁數: 134/170頁
文件大?。?/td> 2717K
代理商: UPSD3234BV-40U6T
uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV
134/170
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE
The JTAG Serial Interface pins (TMS, TCK, TDI,
TDO) are dedicated pins on Port C (see Table
106
). All memory blocks (primary and secondary
Flash memory), PLD logic, and PSD Module Con-
figuration Register Bits may be programmed
through the JTAG Serial Interface block. A blank
device can be mounted on a printed circuit board
and programmed using JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Two additional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up Program and Erase cycles.
By default, on a blank device (as shipped from the
factory or after erasure), four pins on Port C are
the basic JTAG signals TMS, TCK, TDI, and TDO.
Standard JTAG Signals
At power-up, the standard JTAG pins are inputs,
waiting for a JTAG serial command from an exter-
nal JTAG controller device (such as FlashLINK or
Automated Test Equipment). When the enabling
command is received, TDO becomes an output
and the JTAG channel is fully functional. The
same command that enables the JTAG channel
may optionally enable the two additional JTAG sig-
nals, TSTAT and TERR.
The RESET input to the uPS3200 should be active
during JTAG programming. The active RESET
puts the MCU module into RESET Mode while the
PSD Module is being programmed. See Applica-
tion Note AN1153 for more details on JTAG In-
System Programming (ISP).
The uPSD323X Devices supports JTAG In-Sys-
tem-Configuration (ISC) commands, but not
Boundary Scan. The PSDsoft Express software
tool and FlashLINK JTAG programming cable im-
plement the JTAG In-System-Configuration (ISC)
commands.
Table 106. JTAG Port Signals
JTAG Extensions
TSTAT and TERR are two JTAG extension signals
enabled by an “ISC_ENABLE” command received
over the four standard JTAG signals (TMS, TCK,
TDI, and TDO). They are used to speed Program
and Erase cycles by indicating status on uPDS
signals instead of having to scan the status out se-
rially using the standard JTAG channel. See Appli-
cation Note AN1153
TERR indicates if an error has occurred when
erasing a sector or programming a byte in Flash
memory. This signal goes Low (active) when an
Error condition occurs, and stays Low until an
“ISC_CLEAR” command is executed or a chip Re-
set (RESET) pulse is received after an
“ISC_DISABLE” command.
TSTAT behaves the same as Ready/Busy de-
scribed in
Ready/Busy (PC3), page 99
. TSTAT is
High when the PSD Module device is in READ
Mode (primary and secondary Flash memory con-
tents can be read). TSTAT is Low when Flash
memory Program or Erase cycles are in progress,
and also when data is being written to the second-
ary Flash memory.
TSTAT and TERR can be configured as open-
drain type signals during an “ISC_ENABLE” com-
mand.
Security and Flash memory Protection
When the Security Bit is set, the device cannot be
read on a Device Programmer or through the
JTAG Port. When using the JTAG Port, only a Full
Chip Erase command is allowed.
All other Program, Erase and Verify commands
are blocked. Full Chip Erase returns the part to a
non-secured blank state. The Security Bit can be
set in PSDsoft Express Configuration.
All primary and secondary Flash memory sectors
can individually be sector protected against era-
sures. The sector protect bits can be set in PSD-
soft Express Configuration.
INITIAL DELIVERY STATE
When delivered from ST, the uPSD323X Devices
have all bits in the memory and PLDs set to '1.'
The code, configuration, and PLD logic are loaded
using the programming procedure. Information for
programming the device is available directly from
ST. Please contact your local sales representa-
tive.
Port C Pin
JTAG Signals
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
Status (optional)
PC4
TERR
Error Flag (optional)
PC5
TDI
Serial Data In
PC6
TDO
Serial Data Out
相關PDF資料
PDF描述
uPSD3234 Flash Programmable System Device with 8032 Microcontroller Core(嵌入高速“8032微控制器核”的Flash型可編程系統器)
uPSD3251(中文) Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的Flash可編程系統設備)
uPSD3251 Flash Programmable System Devices with 8032 Microcontroller Core(帶8032微控制器內核的Flash可編程系統設備)
uPSD3253AV-24T1T Flash Programmable System Devices with 8032 Microcontroller Core
UPSD3253B Two and Three Channel Codewheels
相關代理商/技術參數
參數描述
UPSD3235A-24T1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3235A-24T1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3235A-24T6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3235A-24T6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core
UPSD3235A-24U1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core