- 您現在的位置：買賣IC網 > PDF目錄379493 > UPD17147CTA1 (NEC Corp.) SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS PDF資料下載
參數資料
| 型號： | UPD17147CTA1 |
| 廠商： | NEC Corp. |
| 英文描述： | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| 中文描述： | 小，通用4位單晶片微控制器 |
| 文件頁數： | 60/102頁 |
| 文件大?。?/td> | 408K |
| 代理商： | UPD17147CTA1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
60
μ
PD17145(A1), 17147(A1), 17149(A1)
17.3 STOP Mode
17.3.1 Setting STOP mode
The STOP mode is set when the STOP instruction is executed.
The operand of the STOP instruction, b
3
b
2
b
1
b
0
, specifies the condition under which the STOP mode is
released.
Table 17-4. STOP Mode Releasing Condition
Format: STOP b
3
b
2
b
1
b
0
B
Bit
STOP mode releasing condition
Note 1
b
3
Enables releasing HALT mode by IRQ
×××
when 1
Notes 2, 4
b
2
Fixed to “0”
b
1
Fixed to “0”
b
0
Enables releasing STOP mode by RLS input when 1
Notes 3, 4
Notes 1.
Only reset (RESET input or POC) is valid when STOP 0000B is specified. When STOP
0000B is executed, the internal circuitry of the microcontroller is initialized to the status
immediately after reset.
IP
×××
must be set to 1. The STOP mode cannot be released by IRQTM1.
b
0
alone cannot be set to 1 (STOP 0001B is prohibited).
Before setting b
0
to 1, be sure to set b
3
to 1.
Even if the STOP instruction is executed with IRQ
×××
= 1 or the RLS input being low, the
STOP instruction is ignored (treated as an NOP instruction), and the STOP mode is not set.
2.
3.
4.
17.3.2 Start address after STOP mode is released
The start address from which the program execution is started after the STOP mode has been released differs
depending on the condition under which the STOP mode has been released, and interrupt enable condition.
Table 17-5. Start Address after STOP Mode Is Released
Releasing Condition
Start Address after Release
Reset
Note 1
Address 0
RLS
Address next to that of STOP instruction
Address next to that of HALT instruction in DI status
IRQ
×××
Note 2
Interrupt vector in EI status
(if two or more IRQ
×××
flags are set, interrupt vector with higher priority)
Notes 1.
RESET input and POC are valid as reset.
IP
×××
must be set to 1. The STOP mode cannot be released by IRQTM1.
2.
相關PDF資料 |
PDF描述 |
|---|---|
| UPD17149 | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17149CT | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17147GT | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17147GTA1 | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17149GTA1 | SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD17147GT | 制造商:NEC 制造商全稱:NEC 功能描述:SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17147GTA1 | 制造商:NEC 制造商全稱:NEC 功能描述:SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17149 | 制造商:NEC 制造商全稱:NEC 功能描述:SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17149CT | 制造商:NEC 制造商全稱:NEC 功能描述:SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
| UPD17149CTA1 | 制造商:NEC 制造商全稱:NEC 功能描述:SMALL, GENERAL-PURPOSE 4-BIT SINGLE-CHIP MICROCONTROLLERS |
發布緊急采購，3分鐘左右您將得到回復。