- 您現在的位置：買賣IC網 > PDF目錄382723 > UMA1022M (NXP SEMICONDUCTORS) Low cost dual frequency synthesizer for radio telephones PDF資料下載
參數資料
| 型號： | UMA1022M |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | XO, clock |
| 英文描述： | Low cost dual frequency synthesizer for radio telephones |
| 中文描述： | PLL FREQUENCY SYNTHESIZER, 2100 MHz, PDSO20 |
| 封裝： | 4.40 MM, PLASTIC, SOT-266-1, SSOP-20 |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 126K |
| 代理商： | UMA1022M |
1998 Dec 09
17
Philips Semiconductors
Product specification
Low cost dual frequency synthesizer for
radio telephones
UMA1022M
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| UPA1817GR-9JG | P-CHANNEL MOS FIELD EFFECT TRANSISTOR FOR SWITCHING |
| UPA1817 | P-CHANNEL MOS FIELD EFFECT TRANSISTOR FOR SWITCHING |
| UPA2707GR-E1 | SWITCHING N-CHANNEL POWER MOSFET |
| UPA2707GR-E1-A | SWITCHING N-CHANNEL POWER MOSFET |
| UPA2707GR-E2 | SWITCHING N-CHANNEL POWER MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UMA10A | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:ULTRAMITE SURFACE MOUNT 500 Watt Transient Voltage Suppressor 5.0 to 170 V |
| UMA10CA | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:ULTRAMITE SURFACE MOUNT 500 Watt Transient Voltage Suppressor 5.0 to 170 V |
| UMA10N | 制造商:ROHM 制造商全稱:Rohm 功能描述:General purpose (dual digital transistors) |
| UMA10NTR | 功能描述:開關晶體管 - 偏壓電阻器 DUAL PNP 50V 100MA RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| UMA11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | 50V V(BR)CEO | 100MA I(C) | SOT-25VAR |
發布緊急采購，3分鐘左右您將得到回復。