參數資料
型號： UCC3976TRPW
廠商： Texas Instruments, Inc.
元件分類： 基準電壓源/電流源
英文描述： Low consumption voltage and current controller for battery chargers and adaptors
中文描述： 鎮流器/背光控制器/驅動器| TSSOP封裝| 8引腳|塑料
文件頁數： 25/28頁
文件大小： 433K
代理商： UCC3976TRPW
SLUS499A
–
NOVEMBER 2001
–
REVISED JANUARY 2002
25
www.ti.com
APPLICATION INFORMATION
burst dimming with the OPEN/SD pin
A burst dimming technique can be used with CCFLs when a wide dimming range is required, this technique can
also yield better efficiency at light loads. Burst dimming is implemented by running the lamp at full current when
on, where the on/off duty factor is controlled a low frequency to provide dimming. In order to prevent visible
flicker, the burst frequency needs to be set higher than 80 Hz.
The UCC397x family is initially targeted for operating the PZT using analog dimming, however, burst dimming
can be implemented by controlling the OPEN/SD pin directly with a square wave. Figure 22 shows burst
dimming performance using the UCC3976 at 125 Hz and 50% duty cycle. In Figures 22
–
25, trace 1 is the drain
connection of the external P- and N-Channel MOSFETs, trace 2 is the OPEN/SD pin which is externally driven
with a 5-V square wave, trace 3 is the COMP pin which is used to lock the operating frequency and trace 4 is
the lamp voltage. These scope graphics were captured with a digital oscilloscope, so aliasing is present in
Figures 22
–
24. Referring back to Figure 22, when OPEN/SD is driven to 5 V the part is in shutdown and the
controller is disabled. When OPEN/SD is forced to 0 V by the external source the controller goes through its
startup sequence with COMP starting at 0 V allowing the PZT to strike the lamp and lock on the frequency
required to regulate the lamp at full current. The size of the feedback capacitor determines the slew rate at which
COMP can lock the system frequency which effects the achievable duty cycle of burst dimming. Fortunately,
the feedback cap with burst dimming can be smaller than with analog dimming since the system small signal
gain is lower at full lamp load. Figures 23 and 24 show burst dimming at approximately 10% and 90% duty cycle
respectively. Figure 25 shows a close up of the startup sequence when OPEN/SD is pulled low. COMP is
preconditioned to 0 V before switching begins and then allowed to ramp up. PZT secondary voltage ramps as
the frequency decreases until the lamp strikes and operates. Strike voltage for the lamp is barely detectable
since the lamp is warm and operating from the previous burst cycles.
VCOMP
VOPEN/SD
VLAMP
VOPEN/SD
Figure 22. UCC3976 Burst Dimming at 50% Duty Cycle
VIN = 12 Vdc
VLAMP = 600 V
fOSC = 125 Hz
50% Duty Cycle
ILAMP = 5 mA
相關PDF資料
PDF描述
UCC3977TRPW BALLAST/BACKLIGHT CONTROLLER/DRIVER|TSSOP|8PIN|PLASTIC
UCC35705DGKTR HIGH - SPEED VOLTAGE MODE PULSE MODE WIDTH MODULATOR
UCC35706DTR HIGH - SPEED VOLTAGE MODE PULSE MODE WIDTH MODULATOR
UCC35706DGKTR Aluminum Electrolytic Radial Lead High Ripple Capacitor; Capacitance: 330uF; Voltage: 400V; Case Size: 25x50 mm; Packaging: Bulk
UCC35705EVM UCC35705 Evaluation Module(UCC35705評估模塊)
相關代理商/技術參數
參數描述
UCC3977PW 功能描述:LCD 驅動器 Multi-Topology Piezoelectric RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
UCC3977PWG4 功能描述:LCD 驅動器 Multi-Topology Piezoelectric RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
UCC3977PWR 制造商:Texas Instruments 功能描述:
UCC40V680UF 制造商:United Chemi-Con 功能描述:AL040X768 85C 13X31
UCC500-30GM-IU-V1 B540 制造商:PEPPERL+FUCHS 功能描述:Sensor, Ultrasonic, Chem Resistant, 094792
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*