- 您現在的位置：買賣IC網 > PDF目錄382720 > UCC3913J Analog IC PDF資料下載
參數資料
| 型號： | UCC3913J |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 158K |
| 代理商： | UCC3913J |
5
UCC1913
UCC2913
UCC3913
I
OUT
I
MAX
I
FAULT
Io(nom)
0A
V
CT
2.5V
0.5V
0V
0V
V
OUT
VSS
t
0
t
1
t
2
t
3
t
4
t
5
t
6
t
7
t
8
t
9
t
10
t
t
t
Output
Current
C
T
Voltage
(w/respecttoVSS)
Output
Voltage
(w/respecttoGND)
APPLICATION INFORMATION (cont.)
Figure 2. Typical timing diagram.
t0: safe condition – output current is nominal, output
voltage is at the negative rail, VSS.
t1: fault control reached – output current rises above
the programmed fault value, CT begins to charge at
36
μ
A.
t2: max current reached – output current reaches the
programmed maximum level and becomes a con-
stant current with value I
MAX
.
t3: fault occurs – CT has charged to 2.5V, fault output
goes high, the FET turns off allowing no output cur-
rent to flow, V
OUT
floats up to ground.
t4: retry – CT has discharged to 0.5V, but fault current
is still exceeded, CT begins charging again, FET is
on, V
OUT
pulled down to VSS.
t5:
t5 = t3: illustrates 3%duty cycle.
t6:
t6 = t4
t7: output short circuit - if V
OUT
is short circuited to
ground, CT charges at a higher rate depending
upon the values for VSS and R
PL
.
t8: fault occurs – output is still short circuited, but the
occurrence of a fault turns the FET off so no current
is conducted.
t9: t9 = t4; output short circuit released, still in fault
mode.
t10: t10 = t0; fault released, safe condition – return to
normal operaton of the circuit breaker.
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料 |
PDF描述 |
|---|---|
| UCH81 | TRIODE HEPTODE |
| UCS51 | Dual step-down main supply controller with auxilary voltages for notebook system power |
| UDA1309H | Low-power stereo bitstream ADC/DAC(低功耗立體聲位流ADC/DAC) |
| UDA1320ATS | Low-Cost Stereo Filter DAC(低價格立體聲濾波數模轉換器) |
| UDA1320 | Low-cost stereo filter DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC3913N | 功能描述:熱插拔功率分布 Neg Floating Single Commercial Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC3913NG4 | 功能描述:熱插拔功率分布 Neg Floating Single Commercial Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC39151DP | 功能描述:熱插拔功率分布 0-3A 7-15V Sngl Hi-Side MOSFET RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC39151DPG4 | 功能描述:熱插拔功率分布 0-3A 7-15V Sngl Hi-Side MOSFET RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC39151DPTR | 功能描述:IC 15V PROG HOT SWAP MGR 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。