- 您現在的位置：買賣IC網 > PDF目錄378722 > UCC2895QTR (Texas Instruments, Inc.) BiCMOS Advanced Phase Shift PWM Controller PDF資料下載
參數資料
| 型號： | UCC2895QTR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | BiCMOS Advanced Phase Shift PWM Controller |
| 中文描述： | BiCMOS工藝先進相移PWM控制器 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 291K |
| 代理商： | UCC2895QTR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
Programming DELAB, DELCD, and the Adaptive Delay Set
The UCC3895 allows the user to set the delay between
switch commands within each leg of the full bridge power
circuit according to the following formula from the data
sheet:
t
R
V
n
DELAY
DEL
DEL
=
+
(
)
sec
25 10
25
12
For this equation V
DEL
is determined in conjunction with
the desire to utilize (or not utilize) the adaptive delay set
feature from the following formula:
(
[
V
V
V
DEL
CS
ADS
=
075
.
)
]
V
+
0 5
.
The following diagram illustrates the resistors needed to
program the delay periods and the adaptive delay set
function.
APPLICATION INFORMATION
6
UCC1895
UCC2895
UCC3895
RAMP:
The Inverting Input of the PWM Comparator. This
pin receives either the CT waveform in voltage and aver-
age current mode controls, or the current signal (plus
slope compensation) in peak current mode control. An in-
ternal discharge transistor is provided on RAMP, which is
triggered during the oscillator dead time.
RT:
Oscillator Timing Resistor. (Refer to Fig. 1, Oscillator
Block Diagram) The oscillator in the UCC3895 operates
by charging an external timing capacitor, CT, with a fixed
current programmed by R
T.
R
T
current is calculated as
follows:
V
R
T
I
RT
=
3 0
where R
T
is in Ohms and I
RT
is in Amperes. R
T
can
range from 40k
to 120k
charging current are also programmed by I
RT
.
SS/DISB:
Soft Start/Disable. This pin combines the two
independent functions.
Soft start charging and dis-
: A
rapid
shutdown
of
the
chip
is
accomplished by any one of the following: externally
forcing SS/DISB below 0.5V, externally forcing REF
below 4V, V
DD
dropping below the UNLO threshold, or an
overcurrent fault is sensed (CS = 2.5V).
In the case of REF being pulled below 4V or an UVLO
condition, SS/DISB is actively pulled to ground via an
internal MOSFET switch. If an overcurrent is sensed,
SS/DISB will sink a current of (10
I
RT
) until SS/DISB
falls below 0.5V.
Note that if SS/DISB is externally forced below 0.5V the
pin will start to source current equal to I
RT
. Also note that
the only time the part switches into the low IDD current
mode is when the part is in undervoltage lockout.
After a fault or disable condition has
passed, VDD is above the start threshold, and/or
SS/DISB falls below 0.5V during a soft stop, SS/DISB will
switch to a soft start mode.
current, equal to I
RT
.
A user-selected capacitor on
SS/DISB determines the soft start (and soft-start) time. In
addition, a resistor in parallel with the capacitor may be
used, limiting the maximum voltage on SS/DISB. Note
that SS/DISB will actively clamp the EAOUT pin voltage
to approximately the SS/DISB pin voltage during both
soft start, soft stop, and disable conditions.
The pin will now source
SYNC:
Oscillator Synchronization. (Refer to Fig. 1, Oscil-
lator Block Diagram) This pin is bidirectional. When used
as an output, SYNC can be used as a clock, which is the
same as the chip’s internal clock. When used as an in-
put, SYNC will override the chip’s internal oscillator and
act as it’s clock signal. This bidirectional feature allows
synchronization of multiple power supplies. The SYNC
signal will also internally discharge the CT capacitor and
any filter capacitors that are present on the RAMP pin.
The internal SYNC circuitry is level sensitive, with an in-
put low threshold of 1.9V, and an input high threshold of
2.1V. A resistor as small as 3.9k
SYNC and GND to reduce the sync pulse width.
may be tied between
VDD:
Power Supply. VDD must be bypassed with a mini-
mum of a 1.0 F low ESR, low ESL capacitor to ground.
REF:
5V,
supplies power to internal circuitry, and can also supply
up to 5mA to external loads. The reference is shut down
during undervoltage lock-out but is operational during all
other disable modes. For best performance, bypass with
a 0.1 F low ESR, low ESL capacitor to ground.
1.2% voltage reference. The reference
PIN DESCRIPTIONS (cont.)
9
11
10
12
DELCD
DELAB
ADS
CS
R
DELCD
R
DELAB
UCC3895
相關PDF資料 |
PDF描述 |
|---|---|
| UCC3895QTR | BiCMOS Advanced Phase Shift PWM Controller |
| UCC2956 | Switch Mode Lithium-Ion Battery Charger Controller |
| UCC2974 | DUAL COLD CATHODE FLUORESCENT LAMP CONTROLLER |
| UCC381-x | Low Dropout 1 Ampere Linear Regulator Family |
| UCC3813PWTR-2 | Low Power Economy BiCMOS Current Mode PWM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC2897AEVM | 功能描述:電源管理IC開發工具 UCC2897A Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| UCC2897APW | 功能描述:電流型 PWM 控制器 Adv Crnt-Mode Active Clamp PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UCC2897APW | 制造商:Texas Instruments 功能描述:Pulse Width Modulation (PWM) Controller 制造商:Texas Instruments 功能描述:IC, CURRENT MODE PWM CTRL, 16V, 20-TSSOP |
| UCC2897APWR | 功能描述:電流型 PWM 控制器 Adv Crnt-Mode Active Clamp PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UCC2897ARGPR | 功能描述:電流型 PWM 控制器 Adv Crnt-Mode Active Clamp PWM Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。