- 您現在的位置：買賣IC網 > PDF目錄380966 > UCC2580J-4 Very low drop voltage regulators with inhibit PDF資料下載
參數資料
| 型號： | UCC2580J-4 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Very low drop voltage regulators with inhibit |
| 中文描述： | 模擬IC |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 395K |
| 代理商： | UCC2580J-4 |
7
UCC1580-1,-2,-3,-4
UCC2580-1,-2,-3,-4
UCC3580-1,-2,-3,-4
Output Configurations
The UCC3580 family of ICs is designed to provide con-
trol functions for single ended active clamp circuits. For
different implementations of the active clamp approach,
different drive waveforms for the two switches (main and
auxiliary) are required. The -3 and -4 versions of the IC
supply
complementary
non-overlapping
(OUT1 and OUT2) with programmable delay which can
be used to drive the main and auxiliary switches. Most
active clamp configurations will require one of these out-
puts to be transformer coupled to drive a floating switch
(e.g. Figure 5). The -1 and -2 versions have the phase of
OUT2 inverted to give overlapping waveforms. This con-
figuration is suitable for capacity coupled driving of a
ground referenced p-channel auxiliary switch with the
OUT2 drive while OUT1 is directly driving an n-channel
main switch (e.g. Figure 4).
waveforms
The programmable delay can be judiciously used to get
zero voltage turn-on of both the main and auxiliary
switches in the active clamp circuits. For the UCC3580, a
single pin is used to program the delays between OUT1
and OUT2 on both sets of edges. Figure 1 shows the re-
lationships between the outputs. Figure 2 gives the ratio
between the two delays. During the transition from main
to auxiliary switch, the delay is not very critical for ZVS
turn-on. For the first half of OUT1 off-time, the body di-
ode of the auxiliary switch conducts and OUT2 can be
turned on any time. The transition from auxiliary to main
switch is more critical. Energy stored in the parasitic in-
ductance(s) at the end of the OUT2 pulse is used to dis-
charge the parasitic capacitance across the main switch
during the delay time. The delay (Delay 1) should be op-
timally programmed at 1/4 the resonant period deter-
mined by parasitic capacitance and the resonant
inductor (transformer leakage and/or magnetizing induc-
tances, depending on the topology). However, depend-
ing on other circuit parasitics, the resonant behavior can
change, and in some cases, ZVS turn-on may not be ob-
tainable. It can be shown that the optimum delay time is
independent of operating conditions for a specific circuit
and should be determined specifically for each circuit.
APPLICATION INFORMATION (cont.)
Figure 4. Active clamp forward converter.
UDG-95071-2
相關PDF資料 |
PDF描述 |
|---|---|
| UCC2580Q-1 | Very low drop voltage regulators with inhibit |
| UCC2580Q-3 | Very low drop voltage regulators with inhibit |
| UCC3588D | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC3588DTR | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
| UCC3588J | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC2580N-1 | 功能描述:電壓模式 PWM 控制器 Single Ended Active Clamp/Reset PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| UCC2580N-1G4 | 功能描述:電壓模式 PWM 控制器 Single Ended Active Clamp/Reset PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| UCC2580N-2 | 功能描述:電壓模式 PWM 控制器 Single Ended Active Clamp/Reset PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| UCC2580N-2G4 | 功能描述:電壓模式 PWM 控制器 Single Ended Active Clamp/Reset PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| UCC2580N-3 | 功能描述:電壓模式 PWM 控制器 Single Ended Active Clamp/Reset PWM RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。