參數資料
型號： UCB1300
廠商： NXP Semiconductors N.V.
英文描述： Advanced modem/audio analog front-end
中文描述： 先進的調制解調器/音頻模擬前端
文件頁數： 46/56頁
文件大?。?/td> 1022K
代理商： UCB1300
1999 Jul 20
46
Philips Semiconductors
Preliminary specification
Advanced modem/audio analog front-end
UCB1300
Notes
1.
2.
3.
4.
Additional test conditions: AUD_DIV[n] = 00001100; input signal 1 kHz, 90 mV (RMS); AUD_IN_ENA = 1.
Coding system for ADC output data is 2’s complement.
See Fig. 35.
Additional test conditions: AUD_DIV[n] = 00001100; 0 dB output attenuation; 90 % of digital full scale input voltage;
16
speaker connected.
Additional test conditions: TEL_DIV[n] = 0101000; 0 dB output attenuation; 90 % of digital full scale input voltage;
1200
load.
Coding system for DAC input data is 2’s complement.
See Fig. 36.
Additional test conditions: TEL_DIV[n] = 0101000; input signal 1 kHz, 300 mV (RMS); TEL_IN_ENA = 1;
TEL_VOICE_ENA = 0.
See Fig. 37.
See Fig. 38.
10. Deviation of the analog output from 0, with 0 code input to telecom output path.
11. The ADC cannot be started or armed if the touch screen circuit is set to interrupt mode (TSC_MODE[n] = 0,0).
12. Coding system for ADC is binary offset.
13. This is a requirement when an odd divisor is set in either the audio or the telecom codec.
14. This is valid for all SIB frame bits 0 to 63, except bits 17 to 20.
15. This is valid for a the SIB frame bits 17 to 20.
16. All curves repeat around the sample frequency f
sa
or f
st
for audio- respectively telecom codec.
17. Any touch-screen resistor above the maximum will not reach full scale and not saturate the ADC
18. The threshold can be used to verify a valid touch using pressure measurement.
5.
6.
7.
8.
9.
t
su(SIBSYNC-SIBCLK)
set-up time SIBSYNC to
SIBCLK falling edge
t
h(SIBSYNC-SIBCLK)
SIBSYNC hold time after
falling edge of SIBCLK
t
su(SIBDIN-SIBCLK)
set-up time SIBDIN to
SIBCLK falling edge
t
h(SIBDIN-SIBCLK)
SIBDIN hold time after
falling edge of SIBCLK
t
(SIBCLK-SIBDOUT)
rising edge of SIBCLK to
valid SIBDOUT
t
(SIBDIN-SIBDOUT)
valid SIBDIN to valid
SIBDOUT
-
15
-
ns
-
10
-
ns
-
15
-
ns
-
10
-
ns
note 14
-
10
-
ns
note 15
-
15
-
ns
Reset circuit
t
W(NRESET)
t
W(rst)
RESET pulse width
internal reset pulse width
5
-
5t
SIBCLK
-
-
ns
ns
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
相關PDF資料
PDF描述
UCB1300BE Advanced modem/audio analog front-end
UCB1400BE Audio codec with touch screen controller and power management monitor
UCB1400 Audio codec with touch screen controller and power management monitor
UCB1500 PCI to AC97 bridge/host controller
UCC1913D Very low drop voltage regulators with inhibit
相關代理商/技術參數
參數描述
UCB1300BE 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end
UCB1400 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor
UCB1400BE 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor
UCB1400BE,128 功能描述:接口—CODEC AUDIO CODEC WITH TOUCHSCREEN RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
UCB1400BE,151 功能描述:接口—CODEC AUDIO CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*