- 您現在的位置：買賣IC網 > PDF目錄382720 > UCB1200 (NXP Semiconductors N.V.) Advanced modem/audio analog front-end PDF資料下載
參數資料
| 型號： | UCB1200 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Advanced modem/audio analog front-end |
| 中文描述： | 先進的調制解調器/音頻模擬前端 |
| 文件頁數： | 53/54頁 |
| 文件大?。?/td> | 1052K |
| 代理商： | UCB1200 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁
1998 Jul 22
53
Philips Semiconductors
Product specification
Advanced modem/audio analog front-end
UCB1200
SOLDERING
Introduction
There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and
surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for
surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often
used.
This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our
“IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all LQFP packages.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the
printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between
50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45
°
C.
Wave soldering
Wave soldering is
not
recommended for LQFP packages. This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following conditions must be observed:
A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering
technique should be used.
The footprint must be at an angle of 45
°
to the board direction and must incorporate solder thieves
downstream and at the side corners.
Even with these conditions, do not consider wave soldering LQFP packages LQFP48 (SOT313-2),
LQFP64 (SOT314-2) or LQFP80 (SOT315-1).
During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within 6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally- opposite end leads. Use only a low voltage soldering iron (less
than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300
°
C. When using a
dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| UCB1200BE | Advanced modem/audio analog front-end |
| UCB1300 | Advanced modem/audio analog front-end |
| UCB1300BE | Advanced modem/audio analog front-end |
| UCB1400BE | Audio codec with touch screen controller and power management monitor |
| UCB1400 | Audio codec with touch screen controller and power management monitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCB1200B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UCB1200B |
| UCB1200BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1300 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1300BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1400 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor |
發布緊急采購，3分鐘左右您將得到回復。