- 您現在的位置：買賣IC網 > PDF目錄381146 > UC2845B (ON SEMICONDUCTOR) High Performance Current Mode Controllers(高性能電流模式控制器) PDF資料下載
參數資料
| 型號： | UC2845B |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | High Performance Current Mode Controllers(高性能電流模式控制器) |
| 中文描述： | 高性能電流模式控制器（高性能電流模式控制器） |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 400K |
| 代理商： | UC2845B |
UC3844B, UC3845B, UC2844B, UC2845B
http://onsemi.com
7
OPERATING DESCRIPTION
The UC3844B, UC3845B series are high performance,
fixed frequency, current mode controllers. They are
specifically designed for OffLine and DCDC converter
applications offering the designer a costeffective solution
with minimal external components. A representative block
diagram is shown in Figure 16.
Oscillator
The oscillator frequency is programmed by the values
selected for the timing components R
T
and C
T
. Capacitor C
T
is charged from the 5.0 V reference through resistor R
T
to
approximately 2.8 V and discharged to 1.2 V by an internal
current sink. During the discharge of C
T
, the oscillator
generates an internal blanking pulse that holds the center
input of the NOR gate high. This causes the Output to be in
a low state, thus producing a controlled amount of output
deadtime. An internal flipflop has been incorporated in the
UCX844/5B which blanks the output off every other clock
cycle by holding one of the inputs of the NOR gate high. This
in combination with the C
T
discharge period yields output
deadtimes programmable from 50% to 70%. Figure 2 shows
R
T
versus Oscillator Frequency and Figure 3, Output
Deadtime versus Frequency, both for given values of C
T
.
Note that many values of R
T
and C
T
will give the same
oscillator frequency but only one combination will yield a
specific output deadtime at a given frequency. The oscillator
thresholds are temperature compensated to within
±
6%
at 50 kHz. Also, because of industry trends moving the
UC384X into higher and higher frequency applications, the
UC384XB is guaranteed to within
±
10% at 250 kHz.
In many noisesensitive applications it may be desirable
to frequencylock the converter to an external system clock.
This can be accomplished by applying a clock signal to the
circuit shown in Figure 18. For reliable locking, the
freerunning oscillator frequency should be set about 10%
less than the clock frequency. A method for multiunit
synchronization is shown in Figure 19. By tailoring the
clock waveform, accurate Output duty cycle clamping can
be achieved to realize output deadtimes of greater than 70%.
Error Amplifier
A fully compensated Error Amplifier with access to the
inverting input and output is provided. It features a typical
dc voltage gain of 90 dB, and a unity gain bandwidth of
1.0 MHz with 57 degrees of phase margin (Figure 6). The
noninverting input is internally biased at 2.5 V and is not
pinned out. The converter output voltage is typically divided
down and monitored by the inverting input. The maximum
input bias current is 2.0 A which can cause an output
voltage error that is equal to the product of the input bias
current and the equivalent input divider source resistance.
The Error Amp Output (Pin 1) is provided for external
loop compensation (Figure 29). The output voltage is offset
by two diode drops (
≈
1.4 V) and divided by three before it
connects to the inverting input of the Current Sense
Comparator. This guarantees that no drive pulses appear at
the Output (Pin 6) when Pin 1 is at its lowest state (V
OL
).
This occurs when the power supply is operating and the load
is removed, or at the beginning of a softstart interval
(Figures 21, 22). The Error Amp minimum feedback
resistance is limited by the amplifier’s source current
(0.5 mA) and the required output voltage (V
OH
) to reach the
comparator’s 1.0 V clamp level:
3.0 (1.0 V) + 1.4 V
0.5 mA
R
f(min)
≈
= 8800
Current Sense Comparator and PWM Latch
The UC3844B, UC3845B operate as a current mode
controller, whereby output switch conduction is initiated by
the oscillator and terminated when the peak inductor current
reaches the threshold level established by the Error
Amplifier Output/Compensation (Pin 1). Thus the error
signal controls the peak inductor current on a
cyclebycycle basis. The Current Sense Comparator PWM
Latch configuration used ensures that only a single pulse
appears at the Output during any given oscillator cycle. The
inductor current is converted to a voltage by inserting the
groundreferenced sense resistor R
S
in series with the
source of output switch Q1. This voltage is monitored by the
Current Sense Input (Pin 3) and compared to a level derived
from the Error Amp Output. The peak inductor current under
normal operating conditions is controlled by the voltage at
Pin 1 where:
V
(Pin 1)
1.4 V
I
pk
=
3 R
S
Abnormal operating conditions occur when the power
supply output is overloaded or if output voltage sensing is
lost. Under these conditions, the Current Sense Comparator
threshold will be internally clamped to 1.0 V. Therefore the
maximum peak switch current is:
I
pk(max)
=
1.0 V
R
S
When designing a high power switching regulator it
becomes desirable to reduce the internal clamp voltage in order
to keep the power dissipation of R
S
to a reasonable level. A
simple method to adjust this voltage is shown in Figure 20. The
two external diodes are used to compensate the internal diodes,
yielding a constant clamp voltage over temperature. Erratic
operation due to noise pickup can result if there is an excessive
reduction of the I
pk(max)
clamp voltage.
A narrow spike on the leading edge of the current
waveform can usually be observed and may cause the power
supply to exhibit an instability when the output is lightly
loaded. This spike is due to the power transformer
interwinding capacitance and output rectifier recovery time.
The addition of an RC filter on the Current Sense Input with
a time constant that approximates the spike duration will
usually eliminate the instability (refer to Figure 24).
相關PDF資料 |
PDF描述 |
|---|---|
| UC3845B | High Performance Current Mode Controllers(高性能電流模式控制器) |
| UC2844Q | OMNIFET FULLY AUTOPROTECTED POWER MOSFET |
| UC1845AY | Digital controlled stereo audio processor |
| UC2844AM | Octal low-side driver for resistive and inductive loads with serial/parallel input control, output protection and diagnostic |
| UC2844AY | OMNIFET FULLY AUTOPROTECTED POWER MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UC2845BAC | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:HIGH PERFORMANCE CURRENT MODE CONTROLLERS |
| UC2845BD | 功能描述:電流型 PWM 控制器 52kHz 1A Current PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC2845BD1 | 功能描述:電流型 PWM 控制器 0.5mA Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC2845BD1013TR | 功能描述:電流型 PWM 控制器 0.5mA Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| UC2845BD1G | 功能描述:電流型 PWM 控制器 52kHz 1A Current PWM w/48% Duty Cycle Max RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。