參數(shù)資料
型號: U4084B
英文描述: Low-Voltage, Voice-Switched Circuit for Hands-Free Operation
中文描述: 低電壓,語音開關電路免提操作
文件頁數(shù): 11/26頁
文件大?。?/td> 544K
代理商: U4084B
U4084B
Preliminary Information
TELEFUNKEN Semiconductors
Rev. A1, 31-Jan-97
11 (26)
The 36-mV offset at the comparator’s input keeps the
comparator from changing state unless the speech level
exceeds the background noise by approximately 4.0 dB.
The time constant of the external RC (approximately
4.5 s) determines the response time to background-noise
variations.
Volume Control
The volume control input at VCI (Pin 10) is sensed as a
voltage w.r.t. V
B
. It affects the attenuators only in receive
mode and has no effect in the idle or transmit modes.
In receive mode, the receive attenuator gain, G
R
, is
6.0 dB, and the transmit attenuator gain, G
T
, is –46 dB
under the condition that VCI = V
B
. When VCI < V
B
, the
receive attenuator gain is reduced (figure 10), whereas the
transmit attenuator gain is increased. Their sum,
however, remains constant. A voltage deviation at VCI
changes the voltage at C
T
, which in turn controls the
attenuators (see “Attenuator Control Block”).
The volume control setting does not affect the maximum
attenuator input signal at which noticeable distortion
occurs.
The bias current at VCI is typically –60 nA. It does not
vary significantly with the VCI voltage or supply voltage
V
S
.
Dial-Tone Detector
The dial-tone detector is a comparator with one side
connected to the receive input (RI) and the other to V
B
with a 15-mV offset (see figure 5). If the circuit is in idle
mode, and the incoming signal is greater than 15 mV (10
mV
rms
), the comparator’s output will change, disabling
the receive idle mode. The receive attenuator will then be
at a setting determined mainly by the volume control.
This circuit prevents the dial tone (which would be
considered as continuous noise) from fading away as the
circuit would have the tendency to switch to the idle
mode. By disabling receive idle mode, the dial tone
remains at the normally expected full level.
12674
to R attenuator
V
B
C4
to attenuator
control
RI
18
Figure 5. Dial-tone detector
AGC
The AGC circuit affects the circuit only in receive mode,
and only when the supply voltage is less than 3.5 V. As V
S
< 3.5 V, the gain of the receive attenuator is reduced (see
figure 13). The transmit path attenuation changes such
that the sum of the transmit and receive gains remains
constant.
The purpose of this feature is to reduce the power (and the
current) used by the speaker when a line-powered
speakerphone is connected to a long line where the
available power is limited. By reducing the speaker
power, the voltage sag at V
S
is controlled, preventing
possible erratic operation.
Attenuator Control Block
The attenuator control block has seven inputs:
The output of the comparator operated by RLO2 and
TLO2 (microphone/speaker side) – designated C1
The output of the comparator operated by RLO1 and
TLO1 (Tip/Ring side) – designated C2
The output of the transmit background-noise monitor
– designated C3
The output of the receive background-noise monitor
– designated C4
The volume control
The dial-tone detector
The AGC circuit
相關PDF資料
PDF描述
U4087B Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4087B-FP Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4090B-N Low power dual voltage comparators
U4090B-NFN Low power dual voltage comparators
U4090B-NFNG3 Low power dual voltage comparators
相關代理商/技術參數(shù)
參數(shù)描述
U4084B-FL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Speakerphone Circuit
U4085B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Technische Daten Technical Data
U4087B 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4087B-FP 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:Low Voltage Voice Switch Interface Circuit for Hands-free Operation in Telephone
U4089B 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT