- 您現在的位置：買賣IC網 > PDF目錄272835 > TXS120ZA-R3H (POWER-ONE INC) 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | TXS120ZA-R3H |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | 2.400 X 3.450 INCH, 0.500 INCH HEIGHT, 3/4 BRICK PACKAGE-14 |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 2635K |
| 代理商： | TXS120ZA-R3H |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Product Specification
TXS Series: 75…120 A DC-DC Converters
36 to 75 V DC Input, 1.2, 1.5, 1.8, 2.0 and 2.5 V Output, 90 W to 250 W
REV. FEB 18, 2003
15 of 27
www.power-one.com
with the negative return Vo (-). More layout
information can be found on the TXS CD ROM.
The following points should be observed, when
sense wires are used:
The output voltage of the TXS modules should
not be increased above +20 % of Uo nom. This
limit includes any increase due to remote
sense and an output voltage set-point
adjustment over the trim function.
The output power of the TXS module is
defined as the output voltages at the power
pins multiplied by the load current. When the
output voltage is increased to compensate
voltage drops, the output power from the
converter is increased as well. The power
should not exceed its maximum rating.
If not used, the remote sense pins have to be
connected as short as possible to Vo (+) and
Vo (-) respectively. If not connected, the
output voltage shows an increased line and
load regulation.
The sense wires are loaded with a small signal
current. Do not place resistors or filters into
the sense wires.
The PCB layout of the power tracks to the load
should result in a low wiring inductance.
Otherwise the dynamic performance even with
sense wires is degraded.
Do not use filter capacitors between sense
and power pins. They could possibly influence
the stability of the module.
Power loss and Efficiency
The measurement of loss and efficiency at very
high output current converters is quite difficult. To
avoid measurement errors, a Kelvin connection
directly at the module terminals should be used.
sense should be wired directly to the power pins.
Vo (+)
Sense (+)
Trim
Sense (-)
Vo (-)
R Load
Uo
Vi (+)
Vi (-)
ON/OFF
6
4
7
8
5
2
3
1
Io
USH = RSHo * Io
Ui
USH = RSHi * Ii
Ii
+
Figure 36:
Efficiency Measurement Set Up
Open sense wires result in measurement errors. A
low drop precision shunt, rated for 100A should be
used to measure the output current.
To remember: At 100 A, a 1 m
resistor in trace
or over a bad contact in the measurement set up
can produce as much as 100 mV of voltage drop
or a measuring error of 100 mV 100 A = 10 W !
The loss and efficiency measurements in the
graphs were done in a test system at room
temperature.
To
calculate
the
approximate
dissipation at elevated base plate temperatures,
the correction factors of the following table can be
used:
I o / TBP
110
100
90
80
70
60
46
100A
1.18
1.12
1.08
1.05
1.03
1.02
1
80A
1.11
1.09
1.07
1.05
1.03
1.01
1
60A
1.07
1.06
1.04
1.03
1.02
1.01
1
Table 7:
Correction
factor
k
for
different
output currents at elevated base
plate temperatures TBP.
Dissipation at TA: PLoss= Pi - Po = Po (1/η - 1)
Dissipation at TBP: PLoss(TBP) = PLoss(Graph) k
The
dissipation
at
elevated
base
plate
temperatures is needed to determine the cooling
requirements ( page 23: Thermal considerations).
Output Over Voltage Protection
The units have a built in over voltage protection,
which prevent an uncontrolled increase of the
output voltage in case of catastrophic failures of
the converter. The over voltage protection consist
of a second control loop, which is independent of
the main regulating circuit.
The protection is set to 125 % Uo set (Models ZY,
ZA, ZB, ZC) and 115 % Uo set (Model ZD).
The over voltage protection is not switching, but
regulating, so that the converter can’t be
accidentally turned of by noise or EMI. Output
voltage adjustment over sense or trim can’t trigger
the over voltage protection, because the protection
level is tracking with Uo set.
Operation in Parallel
Paralleling of two converters is not possible.
Operation in Series
TXS units can be connected in series. Consult the
factory for additional information if a serial
connection of modules is planned.
相關PDF資料 |
PDF描述 |
|---|---|
| TXS120ZY-P21V | 1-OUTPUT 144 W DC-DC REG PWR SUPPLY MODULE |
| TXS75ZY-P2R2V | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| TXS80ZD-3V | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
| TPS61103RGE | 1.8 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PQCC24 |
| TPS2065DBVT | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TXS18X | 制造商:YSTONE 制造商全稱:Yellow Stone Corp 功能描述:TAPED LED LAMP |
| TXS2-1.5V | 功能描述:低信號繼電器 - PCB 2 Form C 2A 30VDC 1.5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| TXS212J | 制造商:Panasonic Electric Works 功能描述: |
| TXS-212V | 制造商:Panasonic 功能描述:Bulk 制造商:Panasonic 功能描述:Electromechanical Relay DPDT 1A 12VDC 2.88KOhm Through Hole |
| TXS2-12V | 功能描述:低信號繼電器 - PCB 1A 12VDC DPDT NON-LATCHING PCB RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
發布緊急采購，3分鐘左右您將得到回復。