- 您現在的位置：買賣IC網 > PDF目錄385949 > TSB14AA1AT (Texas Instruments, Inc.) 3.3 V IEEE 1394-1995 BACKPLANE PHY PDF資料下載
參數資料
| 型號： | TSB14AA1AT |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 3.3 V IEEE 1394-1995 BACKPLANE PHY |
| 中文描述： | 3.3伏電機及電子學工程師聯合會1394-1995底板PHY |
| 文件頁數： | 27/37頁 |
| 文件大?。?/td> | 257K |
| 代理商： | TSB14AA1AT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
6
–
7
6.2
Backplane Environment
6.2.1
Backplane PHY Connection
Typically within a single ended signaling backplane environment, the serial bus is implemented with a pair of signals
(STRB and DATA). The topology is a simple pair of bussed signals as shown in Figure 6
–
6.
PHY
Node
Module
PHY
Node
Module
PHY
Node
Module
PHY
Node
PHY
Node
Module
PHY
Node
STRB
DATA
Backplane Chassis
Figure 6
–
6. Backplane Topology
NOTE:
On a given bus, there can be as many as 63 nodes. There is no restriction on the
distribution of nodes throughout modules on the bus. When more than one node occupies a
module, they must share the same transceivers.
The backplane environment can be implemented with a number of different interface technologies. These include,
but are not limited to: industry-standard gunning transistor logic plus (GTLP), industry-standard transistor-transistor
logic (TTL), backplane transceiver logic (BTL) as defined by IEEE Std 1194 [10] and emitter-coupled logic (ECL).
In addition to the requirements specified by the application environment, the physical media or the serial bus should
meet the requirements defined for media attachment, media signal interface, and media signal timing. Timing
requirements must be met over the ranges specified in the application environment. These include temperature
ranges, voltage ranges, and manufacturing tolerances.
6.2.2
Definition of Logic States
In the open collector environment, the drivers assert the bus to indicate a 1 logic state, or release the bus to indicate
a 0 logic state. To assert the bus, an open collector driver sinks current. To release the bus, drivers are asserted to
a high-impedance state or turned off, allowing the bus signal to be pulled to the termination voltage of the bus.
NOTE:
This typically results in a logical inversion of signals on GTLP, TTL and BTL buses.
Signals on ECL buses typically are not inverted.
All drivers operate in a wired-ORed mode during arbitration. Drivers can operate in a totem pole mode during data
packet and acknowledge transfers. In this mode, a driver can drive the bus into its released state to decrease the rise
time of the bus signal (referred to as a rescinding release with TTL technology).
6.2.3
Bit Rates
Data transmission and reception occurs at 49.152 Mbit/s or 98.304 Mbit/s (
±
100 ppm). In normal operation,
regardless of the interface technology, arbitration occurs at an arbitration clock rate of 49.152 MHz.
[10]
IEEE Std 1194.1
–
1991, IEEE Standard for Electrical Characteristics of Backplane Transceiver Logic (BTL) Interface Circuits
相關PDF資料 |
PDF描述 |
|---|---|
| TSB21LV03BI | IEEE 1394-1995 Triple-Cable Transceiver/Arbiter(IEEE1394-1995 三電纜收發器/判優器) |
| TSB42AA4I | IEEE 1394 A CONSUMER ELECTRONICS LINK LAYER CONTROLLER |
| TSB42AA4PDT | IEEE 1394 A CONSUMER ELECTRONICS LINK LAYER CONTROLLER |
| TSB42AA4PGE | IEEE 1394 A CONSUMER ELECTRONICS LINK LAYER CONTROLLER |
| TSB42AA9I | STORAGELYNX 1394 LINK-LAYER CONTROLLER FOR ATA/ATAPI STORAGE PRODUCTS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB14AA1I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
| TSB14AA1PFB | 功能描述:1394 接口集成電路 3.3V 1-port 50/100 Mbps Backplane PHY RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB14AA1PFBG4 | 功能描述:1394 接口集成電路 3.3V 1-port 50/100 Mbps Backplane PHY RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray |
| TSB14AA1T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecomm/Datacomm |
| TSB14AA1TPFB | 功能描述:IC BACKPLANE PHY 3.3V 48-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。