- 您現在的位置：買賣IC網 > PDF目錄98300 > TS8388BMFSB/QQB3 (ATMEL CORP) 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 PDF資料下載
參數資料
| 型號： | TS8388BMFSB/QQB3 |
| 廠商： | ATMEL CORP |
| 元件分類： | ADC |
| 英文描述： | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| 封裝： | CERAMIC, QFP-68 |
| 文件頁數： | 41/42頁 |
| 文件大?。?/td> | 1307K |
| 代理商： | TS8388BMFSB/QQB3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁
8
TS8388BFS
Product Specification
Parameter
Symb
Test
level
Min
Typ
Max
Unit
SWITCHING PERFORMANCE AND CHARACTERISTICS – See Timing Diagrams Figure 1, Figure 2
Maximum clock frequency
(Note 14)
FS
1
1.4
Gsps
Minimum clock frequency
(Note 15)
FS
4
10
50
Msps
Minimum Clock pulse width (high)
TC1
4
0.280
0.500
50
ns
Minimum Clock pulse width (low)
TC2
4
0.350
0.500
50
ns
Aperture delay
(Note 2)
TA
4
100
+250
400
ps
Aperture uncertainty
(Notes 2, 5)
Jitter
4
0.4
0.6
ps (rms)
Data output delay
(Notes 2, 10, 11, 12)
TOD
4
1150
1360
1660
ps
Output rise/fall time for DATA (20 % – 80 %)
(note 11)
TR/TF
4
250
350
550
ps
Output rise/fall time for DATA READY
(20 % – 80 % )
(note 11)
TR/TF
4
250
350
550
ps
Data ready output delay
(Notes 2,10, 11, 12)
TDR
4
1110
1320
1620
ps
Data ready reset delay
TRDR
4
720
1000
ps
Data to data ready – clock low pulse width
(See timing diagram, notes 9, 13,14)
TOD-
TDR
4
0
40
80
ps
Data to data ready output delay (50% duty cycle)
(See timing diagram, notes 2, 15) @ 1Gsps
TD1
4
420
460
500
ps
Data pipeline delay
TPD
4
clock
cycles
Note 1 : Differential output buffers are internally loaded by 75
resistors. Buffer bias current = 11 mA.
Note 2 : See definition of terms
Note 3 : Histogram testing based on sampling of a 10 MHz sinewave at 50 MSPS.
Note 4 : Output error amplitude <
± 4 LSB around worst code.
Note 5 : Maximum jitter value obtained for single–ended clock input on the JTS8388B die (chip on board) : 200 fs.
(500 fs expected on TS8388BG)
Note 6 : Digital output back termination options depicted in Application Notes figures 3,4,5 .
Note 7 : With a typical value of TD = 465 ps, at 1 Gsps, the timing safety margin for the data storing using the ECLinPS 10E452 output
registers from Motorola is of
± 315 ps, equally shared before and after the rising edge of the Data Ready signals (DR, DRB).
Note 8 : The clock inputs may be indifferently entered in differential or single–ended, using ECL levels or 4 dBm typical power level into the
50
termination resistor of the inphase clock input.
(4 dBm into 50
clock input correspond to 10 dBm power level for the clock generator.)
Note 9 : At 1GSPS, 50/50 clock duty cycle, TC2 = 500 ps (TC1). TDR - TOD = -100 ps (typ) does not depend on the sampling rate.
Note 10 : Specified loading conditions for digital outputs :
- 50
or 75 controlled impedance traces properly 50 / 75 terminated, or unterminated 75 controlled impedance traces.
- Controlled impedance traces far end loaded by 1 standard ECLinPS register from Motorola.( e.g. : 10E452 ) ( Typical input parasitic
capacitance of 1.5 pF including package and ESD protections. )
Note 11 : Termination load parasitic capacitance derating values :
- 50
or 75 controlled impedance traces properly 50 / 75 terminated : 60 ps / pF or 75 ps per additionnal ECLinPS load.
- Unterminated ( source terminated ) 75
controlled impedance lines : 100 ps / pF or 150 ps per additionnal ECLinPS termination
load.
Note 12 : apply proper 50 / 75
impedance traces propagation time derating values : 6 ps / mm (155 ps/inch) for TSEV8388BFS Evaluation
Board.
Note 13 : Values for TOD and TDR track each other over temperature, ( 1 % variation for TOD - TDR per 100
oC. temperature variation ).
Therefore TOD - TDR variation over temperature is negligible. Moreover, the internal ( onchip ) and package skews between each
Data TODs and TDR effect can be considered as negligible.Consequently, minimum values for TOD and TDR are never more than
100 ps apart. The same is true for the TOD and TDR maximum values (see Advanced Application Notes about TOD - TDR variation
over temperature in section 7).
Note 14 : Min value guaranties performance. Max value guaranties functionality.
Note 15 : Min value guaranties functionality. Max value guaranties performance.
相關PDF資料 |
PDF描述 |
|---|---|
| TS8388BMFSB/QQC1 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFSB/QNC3 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFSB/QQB1 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFSB/QNB2 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
| TS8388BMFSB/QNC2 | 1-CH 8-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, CQFP68 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TS8388BVF | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BVFS | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BVGL | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS8388BVGL (+LID) | 制造商:e2v technologies 功能描述:ADC 8-BIT 1 GSPS - Trays |
| TS83C194 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。