參數資料
型號: TPS65573DSST
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 1.5 A SWITCHED CAPACITOR CONVERTER, PDSO12
封裝: 2 X 3 MM, SON-12
文件頁數: 13/16頁
文件大?。?/td> 681K
代理商: TPS65573DSST
PRINCIPLES OF OPERATION
Start/Stop Charging
Charging Status Indication
SLVS868 – MARCH 2009................................................................................................................................................................................................... www.ti.com
Figure 4. Charging Sequence Chart
The TPS65573 has an enable/disable pin for charging (CHG). The only way to start charging is to input a
high-level signal into CHG (see A and C in Figure 2). This high level is latched by internal D-FF shown in
Figure 2. The internal enable (ENA) signal goes up with some delay, which is specified as SW ON after CHG
↑ in
Switching Characteristics. This is to avoid the wrong operation with a pulsed noise at CHG.
To stop charging, there are three trigger events:
Forced stop by inputting a low level at CHG (see B in Figure 4)
Automatic stop by detecting a full charge. VOUT reaches the target value (see D in Figure 4).
Protected stop by detecting an overcurrent protection (OCP) on the SW pin
When the host inputs the high-level signal into CHG, the voltage of VCC and VBAT must meet the recommended
range; VBAT is from 1.4 V to12 V, VCC is from 2.5 V to 5.5 V. It is acceptable to start recharging after a forced
stop controlled by CHG (see C in Figure 4).
When the charging operation is complete, the TPS65573 drives the charge completion indicator pin, XFULL, to a
low level. A controller can detect the status of the device as a logic signal when it is connected through a pullup
resistor (R1) (see Figure 1). The only way to reset the indication at XFULL is to input a low level into CHG (see
The XFULL output enables the controller to find the device-protected situation. If overcurrent protection (OCP)
occurs, XFULL never goes to a low level when CHG is at a high level. Therefore, the controller detects OCP by
measuring the time from turning CHG to a high level to turning XFULL to a low level. If the duration is longer than
the maximum designed charge time, OCP occurs.
6
Copyright 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65573
相關PDF資料
PDF描述
TPS65708YZHT SWITCHING CONTROLLER, PBGA16
TPS65800RTQTG4 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
TPS65800RTQT 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
TPS65800RTQRG4 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56
TPS658600AZQZT POWER SUPPLY MANAGEMENT CKT, PBGA120
相關代理商/技術參數
參數描述
TPS65580EVM-575 制造商:Texas Instruments 功能描述:TPS65580EVM-575 - Boxed Product (Development Kits)
TPS65580PWPR 功能描述:Buck Switching Regulator IC Positive Adjustable 0.764V 3 Output 1.5A, 2.5A 20-TSSOP (0.173", 4.40mm Width) Exposed Pad 制造商:texas instruments 系列:D-CAP2?? 包裝:剪切帶(CT) 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:3 電壓 - 輸入(最小值):4.5V 電壓 - 輸入(最大值):18V 電壓 - 輸出(最小值/固定):0.764V 電壓 - 輸出(最大值):7V 電流 - 輸出:1.5A,2.5A 頻率 - 開關:700kHz 同步整流器:是 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬)裸焊盤 供應商器件封裝:20-HTSSOP 標準包裝:1
TPS65581PWPR 功能描述:Buck Switching Regulator IC Positive Adjustable 0.764V 3 Output 1.5A, 2.5A 20-TSSOP (0.173", 4.40mm Width) Exposed Pad 制造商:texas instruments 系列:D-CAP2?? 包裝:剪切帶(CT) 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:3 電壓 - 輸入(最小值):4.5V 電壓 - 輸入(最大值):18V 電壓 - 輸出(最小值/固定):0.764V 電壓 - 輸出(最大值):7V 電流 - 輸出:1.5A,2.5A 頻率 - 開關:700kHz 同步整流器:是 工作溫度:-40°C ~ 85°C(TA) 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬)裸焊盤 供應商器件封裝:20-HTSSOP 標準包裝:1
TPS65630ARTGR 制造商:Texas Instruments 功能描述:
TPS65631DPDR 制造商:Texas Instruments 功能描述:IC AMOLED DISPLAY DUAL 12WSON 制造商:Texas Instruments 功能描述:Dual Output AMOLED Display PWR supply