- 您現在的位置：買賣IC網 > PDF目錄220069 > TPS65021RHARG4 (TEXAS INSTRUMENTS INC) 3-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC40 PDF資料下載
參數資料
| 型號： | TPS65021RHARG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC40 |
| 封裝： | 6 X 6 MM, GREEN, PLASTIC, MO-220/VJJD-2, QFN-40 |
| 文件頁數： | 15/47頁 |
| 文件大?。?/td> | 1180K |
| 代理商： | TPS65021RHARG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
POWER SAVE MODE OPERATION
I
=
PFMDCDC1 enter
I
=
PFMDCDC2 enter
I
=
PFMDCDC3 enter
VINDCDC1
VINDCDC2
VINDCDC3
24 W
26 W
39 W
(1)
I
=
PFMDCDC1 leave
I
=
PFMDCDC2 leave
I
=
PFMDCDC3 leave
VINDCDC1
VINDCDC2
VINDCDC3
18 W
20 W
29 W
(2)
SLVS613B – OCTOBER 2005 – REVISED JULY 2007
DETAILED DESCRIPTION (continued)
During PWM operation, the converters use a unique fast response voltage mode controller scheme with input
voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the P-channel MOSFET switch is
turned on. The inductor current ramps up until the comparator trips and the control logic turns off the switch. The
current limit comparator also turns off the switch if the current limit of the P-channel switch is exceeded. After the
adaptive dead time used to prevent shoot through current, the N-channel MOSFET rectifier is turned on, and the
inductor current ramps down. The next cycle is initiated by the clock signal, again turning off the N-channel
rectifier and turning on the P-channel switch.
The three dc-dc converters operate synchronized to each other with the VDCDC1 converter as the master. A
180
° phase shift between the VDCDC1 switch turn on and the VDCDC2 and a further 90° shift to the VDCDC3
switch turn on decreases the input RMS current and smaller input capacitors can be used. This is optimized for
a typical application where the VDCDC1 converter regulates a Li-Ion battery voltage of 3.7 V to 3.3 V, the
VDCDC2 converter from 3.7 V to 2.5 V, and the VDCDC3 converter from 3.7 V to 1.5 V. The phase of the three
converters can be changed using the CON_CTRL register.
As the load current decreases, the converters enter the power save mode operation. During PSM, the
converters operate in a burst mode (PFM mode) with a frequency between 750 kHz and 1.5 MHz, nominal for
one burst cycle. However, the frequency between different burst cycles depends on the actual load current and
is typically far less than the switching frequency with a minimum quiescent current to maintain high efficiency.
In order to optimize the converter efficiency at light load, the average current is monitored and if in PWM mode
the inductor current remains below a certain threshold, then PSM is entered. The typical threshold to enter PSM
is calculated as follows:
During the PSM the output voltage is monitored with a comparator, and by maximum skip burst width. As the
output voltage falls below the threshold, set to the nominal VO, the P-channel switch turns on and the converter
effectively delivers a constant current defined as follows.
If the load is below the delivered current then the output voltage rises until the same threshold is crossed in the
other direction. All switching activity ceases, reducing the quiescent current to a minimum until the output
voltage has again dropped below the threshold. The power save mode is exited, and the converter returns to
PWM mode if either of the following conditions are met:
1. the output voltage drops 2% below the nominal VO due to increasing load current
2. the PFM burst time exceeds 16
× 1/fs (10.67 μs typical).
22
相關PDF資料 |
PDF描述 |
|---|---|
| TS3809CXERF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| TC151A6023EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B4332EOA713 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B5933EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
| TC151B5735EOA723 | 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65021RHAT | 功能描述:電池管理 6-Ch Pwr Mgmt IC for Li-Ion Systems RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65021RHATG4 | 功能描述:電池管理 6-Ch Pwr Mgmt IC for Li-Ion Systems RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65022RHAR | 功能描述:電池管理 Pwr Mgmt IC for Li-Ion Pwred Sys RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65022RHARG4 | 功能描述:電池管理 Pwr Mgmt IC for Li-Ion Pwred Sys RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65022RHAT | 功能描述:電池管理 Pwr Mgmt IC for Li-Ion Pwred Sys RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。