參數資料
型號: TPS62208DBV
廠商: TEXAS INSTRUMENTS INC
元件分類: 穩壓器
英文描述: 0.67 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO5
封裝: PLASTIC, SOT-23, 5 PIN
文件頁數: 4/22頁
文件大?。?/td> 461K
代理商: TPS62208DBV
www.ti.com
APPLICATION INFORMATION
ADJUSTABLE OUTPUT VOLTAGE VERSION
Vout + 0.5 V
1 )
R1
R2
C1 +
1
2
p
10 kHz
R1
C2 +
R1
R2
C1
VI
GND
EN
SW
FB
C3
4.7
F
L1
10
H
C4
10
F
TPS62200
VI
2.5 V 6 V
VO
1.8 V / 300 mA
R1
470k
R2
180k
C1
33 pF
C2
100 pF
INDUCTOR SELECTION
SLVS417E – MARCH 2002 – REVISED MAY 2006
When the adjustable output voltage version TPS62200 is used, the output voltage is set by the external resistor
divider. See Figure 16.
The output voltage is calculated as
R1 + R2
≤ 1 M and internal reference voltage V(ref)typ = 0.5 V
R1 + R2 should not be greater than 1 M
for reasons of stability. To keep the operating quiescent current to a
minimum, the feedback resistor divider should have high impedance with R1+R2
≤ 1 M. Because of the high
impedance and the low reference voltage of Vref = 0.5 V, the noise on the feedback pin (FB) needs to be
minimized. Using a capacitive divider C1 and C2 across the feedback resistors minimizes the noise at the
feedback without degrading the line or load transient performance.
C1 and C2 should be selected as
R1 = upper resistor of voltage divider
C1 = upper capacitor of voltage divider
For C1 a value should be chosen that comes closest to the calculated result.
R2 = lower resistor of voltage divider
C2 = lower capacitor of voltage divider
For C2 the selected capacitor value should always be selected larger than the calculated result. For example, in
Figure 16 for C2, 100 pF are selected for a calculated result of C2 = 86.17 pF.
If quiescent current is not a key design parameter, C1 and C2 can be omitted, and a low-impedance feedback
divider must be used with R1+R2 <100 k
. This design reduces the noise available on the feedback pin (FB) as
well, but increases the overall quiescent current during operation.
Figure 16. Typical Application Circuit for the Adjustable Output Voltage
The TPS6220x device is optimized to operate with a typical inductor value of 10 H.
For high efficiencies, the inductor should have a low dc resistance to minimize conduction losses. Although the
inductor core material has less effect on efficiency than its dc resistance, an appropriate inductor core material
must be used.
12
相關PDF資料
PDF描述
TPS40055PWP SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16
TPS3824-30DBVRG4 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO5
TPS2300IPWG4 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20
TC151A2013EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A6022EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS62208DBVR 功能描述:直流/直流開關調節器 1.875V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62208DBVRG4 功能描述:直流/直流開關調節器 1.875V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62208DBVT 功能描述:直流/直流開關調節器 1.875V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62208DBVTG4 功能描述:直流/直流開關調節器 1.875V Out Hi-Eff Step-Down Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS62220DDCR 功能描述:直流/直流開關調節器 Adj 400mA Hi-Eff Step-Down Con 15uA RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5