參數資料
型號： TPS5625CPWPR
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, PDSO28
封裝： PLASTIC, TSSOP-28
文件頁數： 16/25頁
文件大小： 387K
代理商： TPS5625CPWPR
TPS5615, TPS5618, TPS5625, TPS5633
SYNCHRONOUS-BUCK HYSTERETIC REGULATOR CONTROLLER
SLVS177A – SEPTEMBER 1998 – REVISED NOVEMBER 1998
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
layout guidelines
Good power supply results will only occur when care is given to proper design and layout. Layout will affect noise
pickup and generation and can cause a good design to perform with less than expected results. With a range
of currents from milliamps to tens or even hundreds of amps, good power supply layout is much more difficult
than most general PCB design. The general design should proceed from the switching node to the output, then
back to the driver section and, finally, place the low-level components. Below are several specific points to
consider before layout of a TPS56xx design begins.
1.
All sensitive analog components should be referenced to ANAGND. These include components connected
to SLOWST, IOUT, OCP, VSENSE, VREFB, VHYST, BIAS, and LOHIB.
2.
Analog ground and drive ground should be isolated as much as possible. Ideally, analog ground will connect
to the ground side of the bulk storage capacitors, on VO, and drive ground will connect to the main ground
plane close to the source of the low-side FET.
3.
Connections from the drivers to the gate of the power FETs should be as short and wide as possible to
reduce stray inductance. This becomes more critical if external gate resistors are not being used.
4.
The bypass capacitor for the DRV regulator should be placed close to the TPS56xx and be connected to
DRVGND.
5.
The bypass capacitor for VCC should be placed close to the TPS56xx and be connected to DRVGND.
6.
When configuring the high-side driver as a floating driver, the connection from BOOTLO to the power FETs
should be as short and as wide as possible. The other pins that also connect to the power FETs, LOHIB
and LOSENSE, should have a separate connection to the FETs, since BOOTLO will have large peak
currents flowing through it.
7.
When configuring the high-side driver as a floating driver, the bootstrap capacitor (connected from BOOT
to BOOTLO) should be placed close to the TPS56xx.
8.
When configuring the high-side driver as a ground referenced driver, BOOTLO should be connected to
DRVGND.
9.
The bulk storage capacitors across VI should be placed close to the power FETs. High-frequency bypass
capacitors should be placed in parallel with the bulk capacitors and connected close to the drain of the
high-side FET and close to the source of the low-side FET.
10. High-frequency bypass capacitors should be placed across the bulk storage capacitors on VO.
11. HISENSE and LOSENSE should be connected very close to the drain and source, respectively, of the
high-side FET. HISENSE and LOSENSE should be routed very close to each other to minimize
differential-mode noise coupling to these traces.
相關PDF資料
PDF描述
TPS56221DQPR SWITCHING CONTROLLER, PDSO22
TPS57040QDGQRQ1 SWITCHING REGULATOR, 2500 kHz SWITCHING FREQ-MAX, PDSO10
TPS57114QRTERQ1 SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC16
TPS60100PWP 0.2 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20
TPS60101PWPG4 SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20
相關代理商/技術參數
參數描述
TPS5625EVM-105 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
TPS5625EVM-112 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
TPS5625PWP 功能描述:開關變換器、穩壓器與控制器 High Current Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS5625PWPG4 功能描述:開關變換器、穩壓器與控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
TPS5625PWPRG4 功能描述:DC/DC 開關控制器 High Crnt Synch Buck Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*