- 您現在的位置：買賣IC網 > PDF目錄365925 > TPS5618CPWPR Voltage-Mode SMPS Controller PDF資料下載
參數資料
| 型號： | TPS5618CPWPR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Voltage-Mode SMPS Controller |
| 中文描述： | 電壓模式開關電源控制器 |
| 文件頁數： | 13/34頁 |
| 文件大?。?/td> | 811K |
| 代理商： | TPS5618CPWPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
TPS56302
DUAL-OUTPUT LOW-INPUT-VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289A
–
MARCH 2000
–
REVISED OCTOBER 2000
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
detailed description (continued)
deadtime control
Deadtime control prevents shoot-through current from flowing through the main power FETs during switching
transitions by actively controlling the turnon time of the MOSFET drivers. The high-side driver is not allowed
to turn on until the gate drive voltage to the low-side FET is below 1 V, and the low-side driver is not allowed
to turn on until the voltage at the junction of the 2 FETs (Vphase) is below 2 V.
current sensing
Current sensing is achieved by sampling and holding the voltage across the high-side power FET while the
high-side FET is on. The sampling network consists of an internal 60-
switch and an external hold capacitor.
Internal logic controls the turnon and turnoff of the sample/hold switch such that the switch does not turn on until
the Vphase voltage transitions high, and the switch turns off when the input to the high-side driver goes low.
Thus sampling will occur only when the high-side FET is conducting current. The voltage on the IOUT pin equals
2 times the sensed high-side voltage.
droop compensation
The droop compensation network reduces the load transient overshoot / undershoot on V
OUT
, relative to V
REF
(see the
application information
section of this document for more details). V
OUT
is programmed to a voltage
greater than V
REF
by an external resistor divider from V
OUT
to the VSENSE pin to reduce the undershoot on
V
OUT
during a low to high load transient. The overshoot during a high to low load transient is reduced by
subtracting the voltage that is on the DROOP pin from V
REF
. The voltage on the IOUT pin is divided down with
an external resistor divider, and connected to the DROOP pin.
inhibit
INHIBIT is a TTL-compatible comparator pin that is used to enable the controller. When INHIBIT is lower than
the threshold, the output drivers are low and the slow-start capacitor is discharged. When INHIBIT goes high
(above 2.1 V), the short across the slow-start capacitor is released and normal converter operation begins.
When another system logic supply is connected to the INHIBIT pin, this pin controls power sequencing by
locking out controller operation until the system logic supply exceeds the input threshold voltage of the inhibit
circuit; thus the +3.3-V supply and another system logic supply (either +5 V or +12 V) must be above UVLO
thresholds before the controller is allowed to start up. Toggling the INHIBIT pin from low to high or recycling V
CC
clears the fault latch.
slow-start
The slow-start circuit controls the rate at which both V
OUT
–
RR
and V
OUT
–
LDO
power up (at the same time). A
capacitor is connected between the SLOWST and ANAGND pins and is charged by an internal current source.
The value of the current source is proportional to the reference voltage, so that the charging rate of C
SLOWST
is proportional to the ripple regulator reference voltage. The slow-start charging current is determined by the
following equation:
ISLOWSTART
IVREFB
5
Where I
VREFB
is the current flowing out of the VREFB pin. It is recommended that no additional loads be
connected to VREFB, other than the resistor divider for setting the hysteresis voltage. Thus these resistor values
will determine the slow-start charging current. The maximum current that can be sourced by the VREFB circuit
is 500
μ
A. The equation for the slow-start time is:
TSLOWSTART
5
CSLOWSTART
RVREFB
Where R
VREFB
is the total external resistance from VREFB to ANAGND.
相關PDF資料 |
PDF描述 |
|---|---|
| TPS5625CPWPR | Voltage-Mode SMPS Controller |
| TPS60100PWPR | Analog IC |
| TPS60101PWPR | Analog IC |
| TPS60110PWPR | Analog IC |
| TPS60111PWPR | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS5618EVM-106 | 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5618EVM-113 | 功能描述:HIGH-PERFORMANCE SYNCHRONOUS BUC RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| TPS5618PWP | 功能描述:DC/DC 開關控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS5618PWPG4 | 功能描述:DC/DC 開關控制器 Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS562200DDCR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.765V 1 Output 2A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.765V 電壓 - 輸出（最大值）:7V 電流 - 輸出:2A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:6-SOT 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。