- 您現在的位置：買賣IC網 > PDF目錄69510 > TPS51120RHBRG4 (TEXAS INSTRUMENTS INC) 0.1 A DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PQCC32 PDF資料下載
參數資料
| 型號： | TPS51120RHBRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩(wěn)壓器 |
| 英文描述： | 0.1 A DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | GREEN, PLASTIC, QFN-32 |
| 文件頁數： | 5/39頁 |
| 文件大?。?/td> | 826K |
| 代理商： | TPS51120RHBRG4 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
www.ti.com
Light Load Operation
I
OUT(LL) +
1
2
L
f
V
IN * VOUT
V
OUT
V
IN
(1)
Forced PWM Operation
5V, 100 mA, LDO and Switchover (VREG5)
SLUS670B – JULY 2005 – REVISED FEBRUARY 2007
DETAILED DESCRIPTION (continued)
TPS51120 automatically reduces switching frequency at light load condition to maintain high efficiency. This
reduction of frequency is achieved smoothly and without an increase in load regulation. Detail operation is
described as follows. As the output current decreases from heavy load condition, the inductor current is also
reduced and eventually comes to the point that its ‘valley’ touches zero current, which is the boundary between
continuous conduction and discontinuous conduction modes. The rectifying MOSFET is turned off when this
zero inductor current is detected. The on-time is kept the same as that in the heavy load condition. As the load
current further decreases, the converter runs in discontinuous conduction mode and it takes longer and longer to
discharge the output capacitor to the level that requires next ‘ON’ cycle. This results in reducing the switching
frequency. In reverse, when the output current increases from light load to heavy load, switching frequency
increases to the constant predetermined frequency as the inductor current reaches to the continuous
conduction. The transition load point to the light load operation IOUT(LL) (i.e. the threshold between continuous
and discontinuous conduction mode) can be calculated as shown in Equation 1.
where f is the PWM switching frequency which is determined by TONSEL pin. Switching frequency versus
output current in the light load condition is a function of L, f, VIN and VOUT, but it decreases almost proportional to
Tying SKIPSEL to V5FILT or leaving it float force the part to operate in continuous conduction mode for entire
load range by disabling zero inductor current detection. Switching frequency is kept at the frequency selected by
TONSEL input. System designers may want to use this mode to avoid certain frequency in light load condition
with the cost of low efficiency. However, please be aware the output has a capability to both sink and source
current in this mode. If the output terminal is connected to a voltage source higher than the regulated voltage,
the converter sinks current from the output and boosts the charge into the input capacitor. This may cause
unexpected high voltage at VIN and may damage the part.
A 5-V, 100-mA linear regulator is integrated in the TPS51120. This low drop-out (LDO) regulator services the
main analog supply rail for the IC and provides the current for the gate drivers. The regulator is a PMOS type
with transconductance control and the pole is determined by the value of output capacitance. Typically, the
value of this capacitor must be greater than 4.7
F. A 10-F ceramic capacitor is recommended for a typical
design. Current limit and thermal protection are included in the regulator. Additionally, if the VO1 voltage
exceeds 4.8 V, then the regulator is switched off and the 5V rails are bootstrapped to the 5-V switcher output,
improving the efficiency of the converter. A glitch-free switchover is accomplished. The VREG5 output voltage
does not show a short “glitch” down to 4.8 V when this bootstrapping action is taken. The switchover impedance
from VO1 to VREG5 is typically 1.3
. Standby current is designed for 30-A operation allowing the user to
leave the regulator alive while maintaining maximum battery life. The EN5 pin is a high voltage input and can be
tied to VBAT or left open to enable the 5-V regulator. This 5-V regulator must be enabled prior to enable
switching regulators. Pull EN5 to ground to shut off the regulator. Disabling the regulator does not promise
shutting down the switchers once 5 volts is supplied via the bootstrap path. Because switchover occurs, the 5-V
switcher MUST be turned off with the LDO in order to shut down the device. EN5 does NOT function as a
master disable.
13
相關PDF資料 |
PDF描述 |
|---|---|
| TPS51120RHBR | 0.1 A DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS51120RHBT | 0.1 A DUAL SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PQCC32 |
| TPS51123ARGET | SWITCHING REGULATOR, PQCC24 |
| TPS51123ARGER | SWITCHING REGULATOR, PQCC24 |
| TPS5120DBTG4 | 1.5 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO30 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS51120RHBT | 功能描述:電流型 PWM 控制器 Dual Current Mode Sync Step-Down RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| TPS51120RHBTG4 | 功能描述:電流型 PWM 控制器 Dual Current Mode Sync Step-Down RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| TPS51123 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Dual-Synchronous, Step-Down Controller with Out-of-Audio? Operation and 100-mA LDOs for Notebook System Power |
| TPS51123A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Dual-Synchronous, Step-Down Controller with Out-of-Audioa?￠ Operation and 100-mA LDOs for Notebook System Power |
| TPS51123ARGER | 功能描述:DC/DC 開關控制器 Dual-Sync,Step- Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發(fā)布緊急采購，3分鐘左右您將得到回復。