參數資料
型號： TPS43000PWG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16
封裝： GREEN, TSSOP-16
文件頁數： 8/31頁
文件大?。?/td> 615K
代理商： TPS43000PWG4
TPS43000
SLUS489 OCTOBER 2001
16
www.ti.com
APPLICATION INFORMATION
With voltage-mode control, the closed-loop design goal for each of the topologies with the Type III error amplifier
compensation is to set the crossover frequency above the resonant frequency of the LC filter (prevents filter
oscillations during a transient response), but below the lowest possible RHP zero frequency. This is
accomplished by setting the two zeros in the compensation network before the LC double pole frequency. This
provides a phase boost. The two poles should be placed a decade above the crossover frequency.
The following is a typical procedure for selecting the loop compensation values for a buck converter operated
in CCM:
Step 1. Select the desired crossover frequency a decade above the LC pole frequency.
Step 2. Set the resistor divider formed by R1 and RBIAS to develop the desired regulation voltage. Note that
RBIAS sets the dc operating point of the loop, but has no effect on ac operation and does not factor into
the loop compensation calculations.
Step 3. Set the zero formed by R1 and C3 to approximately one-half decade above the LC double pole to
compensate for the phase loss.
Step 4. Set the zero formed by R2 and C1 to approximately one-half decade below the LC double pole to avoid
a conditional instability.
Step 5. Set the pole formed by R3 and C3 to cancel the ESR zero of the output capacitor.
Step 6. Set the pole formed by R2 and C2 to approximately one-half decade above the crossover frequency.
If the converter is operated in DCM, the lead network (R3 and C3 in Figure 2) can be eliminated for all topologies.
This configuration is referred to as a Type II error amplifier compensation network and has a pole at the origin
and a single zero-pole pair. It can provide up to 90
° of phase boost. The frequency of the pole and zero are
defined by the following equations:
zero
f
z1 +
1
(2
p
R2
C1)
pole
f
p1 [
1
(2
p
R2
C2)
, Assuming C1
C2
The zero-pole pair is used to compensate for the power circuit’s ESR zero and the pole formed by the output
capacitor and the effective output resistance.
(15)
(16)
相關PDF資料
PDF描述
TC151B2031EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2239EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A5748EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2435EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2138EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS43000PWR 功能描述:DC/DC 開關控制器 Multi-Topology High Freq DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS43000PWRG4 功能描述:DC/DC 開關控制器 Multi-Topology High Freq DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS43060 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Quiescent Current Synchronous Boost DC-DC Controller with Wide VIN Range
TPS43060EVM-199 功能描述:電源管理IC開發工具 TPS43060 EVAL MOD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS43060RTER 功能描述:DC/DC 開關控制器 Sync Boost Cntlr Wide Input Vtg RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*