參數資料
型號： TPS43000PWG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, 2000 kHz SWITCHING FREQ-MAX, PDSO16
封裝： GREEN, TSSOP-16
文件頁數： 6/31頁
文件大?。?/td> 615K
代理商： TPS43000PWG4
TPS43000
SLUS489 OCTOBER 2001
14
www.ti.com
APPLICATION INFORMATION
error amplifier
The TPS43000 uses voltage mode control for each of the topologies. The output voltage is sensed and fed back
to the FB pin (inverting input) and compared to an internal 800 mV reference connected to the non-inverting
input. The difference (i.e. error voltage), is amplified by the internal error amplifier. The output of the error
amplifier (COMP), is then compared to the oscillator sawtooth ramp to control the pulse width used to drive the
power switch (energizing MOSFET). The duty cycle is varied to regulate the output voltage. The higher the error
voltage, the longer the energizing MOSFET switch is on.
The transient response of a converter is a function of both small signal and large signal responses. The small
signal response is determined by the error amplifier’s loop compensation (feedback network), whereas the large
signal response is a function of the error amplifier’s gain bandwidth and slew rate (dv/dt) as well as the slew
rate of the inductor current (di/dt). The TPS43000 internal error amplifier has a 5-MHz unity gain bandwidth. This
almost assures that the loop bandwidth is limited by external circuit characteristics rather than error amplifier
limitations. The internal error amplifier is capable of sourcing and sinking an ensured 500
A, which assures
that even during large signal transients, external components determine circuit behavior. Using low feedback
capacitance allows the error amplifier to rapidly slew from one level to another, insuring excellent transient
response.
loop compensation
The voltage loop needs to be compensated to provide control loop stability margin, and to minimize the output
voltage overshoot/undershoot response to line and load transients. A Type III error amplifier compensation
network can be used to optimize the loop response for any of the topologies and operating modes implemented
with the TPS43000. The Type III amplifier circuit is shown in Figure 2. This configuration has a pole at the origin
and two zero-pole pairs. It can provide up to 180
° of phase boost.
VOUT
C3
RBIAS
VREF
R3
R1
C1
R2
+
C2
Figure 2. Type III Error Amplifier Compensation
Network
0 dB
Av1
Av2
fz1
fz2
fp1
fp2
Gain
d
B
Figure 3. Type III Error Amplifier Compensation
Gain Response
t Time ns
相關PDF資料
PDF描述
TC151B2031EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2239EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151A5748EOA723 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2435EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC151B2138EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
TPS43000PWR 功能描述:DC/DC 開關控制器 Multi-Topology High Freq DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS43000PWRG4 功能描述:DC/DC 開關控制器 Multi-Topology High Freq DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS43060 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low Quiescent Current Synchronous Boost DC-DC Controller with Wide VIN Range
TPS43060EVM-199 功能描述:電源管理IC開發工具 TPS43060 EVAL MOD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS43060RTER 功能描述:DC/DC 開關控制器 Sync Boost Cntlr Wide Input Vtg RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*