參數資料
型號： TPS2311PW
廠商： Texas Instruments, Inc.
英文描述： DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT CIRCUIT BREAKER AND POWER-GOOD REPORTING
中文描述： 雙熱插拔功率相互依賴的斷路器及功率控制器，高質量的報告
文件頁數： 18/22頁
文件大小： 423K
代理商： TPS2311PW
TPS2310, TPS2311
DUAL HOT SWAP POWER CONTROLLER WITH INTERDEPENDENT
CIRCUIT BREAKER AND POWER-GOOD REPORTING
SLVS275B – FEBRUARY 2000 – REVISED APRIL 2000
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
setting the power good threshold voltage
The two feedback resistors R
VSENSEx_TOP
and R
VSENSEx_BOT
connected between V
Ox
and ground form a
resistor divider setting the voltage at the VSENSEx pins. VSENSE1 voltage equals to
V
I(SENSE1)
= V
O
×
R
VSENSE1_BOT
/(R
VSENSE1_TOP
+ R
VSENSE1_BOT
)
This voltage is compared to an internal voltage reference (1.225 V
±
2%) to determine whether the output voltage
level is within a specified tolerance. For example, given a nominal output voltage at V
O1
, and defining V
O1_min
as the minimum required output voltage, then the feedback resistors are defined by:
R
VSENSE1_TOP
V
O1_min
1.225
1.225
R
VSENSE1_BOT
Start the process by selecting a large standard resistor value for R
VSENSE1_BOT
to reduce power loss. Then
R
VSENSE1_TOP
can be calculated by nserting all of the known values nto the equation above. When V
O1
s ower
than V
O1_min
, PWRGD1 will be low as long as the controller is enabled.
undervoltage lockout (UVLO)
The TPS2310/11 includes an undervoltage lockout (UVLO) feature that monitors the voltage present on the
VREG pin. This feature will disable both external MOSFETs if the voltage on VREG drops below 2.78 V
(nominal) and will re-enable normal operation when it rises above 2.85 V (nominal). Since VREG is fed from
IN1 through a low-dropout voltage regulator, the voltage on VREG will track the voltage on IN1 within 50 mV.
While the undervoltage lockout is engaged, both GATE1 and GATE2 are held low by internal PMOS pulldown
transistors, ensuring that the external MOSFET transistors remain off at all times, even if all power supplies have
fallen to 0 V.
single-channel operation
Some applications may require only a single external MOS transistor. Such applications should use GATE1 and
the associated circuitry (IN1, ISENSE1, ISET1, DISCH1). The IN2 pin should be grounded to disable the
circuitry associated with the GATE2 pin. The VSENSE2 and PWRGD2 circuitry is unaffected by disabling
GATE2, and may still be used if so desired.
power-up control
The TPS2310/11 includes a 500
μ
s (nominal) startup delay that ensures that internal circuitry has sufficient time
to start before the device begins turning on the external MOSFETs. This delay is triggered only upon the rapid
application of power to the circuit. If the power supply ramps up slowly, the undervoltage lockout circuitry will
provide adequate protection against undervoltage operation.
3-channel hot-swap application
Some applications require hot-swap control of up to three voltage rails, but may not explicitly require the sensing
of the status of the output power on all three of the voltage rails. One such application is device bay, where dv/dt
control of 3.3 V, 5 V, and 12 V is required. By using channel 2 to drive both the 3.3-V and 5-V power rails and
channel 1 to drive the 12-V power rail, as is shown below, TPS2310/11 can deliver three different voltages to
three loads while monitoring the status of two of the loads.
相關PDF資料
PDF描述
TPS2320D DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2320PW DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2321D DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2321PW DUAL HOT SWAP POWER CONTROLLER WITH INDEPENDENT CIRCUIT BREAKER
TPS2330D SINGLE HOT SWAP POWER CONTROLLER WITH CIRCUIT BREAKER AND POWER-GOOD REPORTING
相關代理商/技術參數
參數描述
TPS2320ID 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDG4 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDR 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IDRG4 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2320IPW 功能描述:熱插拔功率分布 3-13V Dual w/Ind Chl Circuit Breaking RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*