參數資料
型號： TPIC74100QPWPRQ1
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 2.5 A SWITCHING REGULATOR, 440 kHz SWITCHING FREQ-MAX, PDSO20
封裝： GREEN, PLASTIC, HTSSOP-20
文件頁數： 3/30頁
文件大小： 781K
代理商： TPIC74100QPWPRQ1
www.ti.com
Buck SMPS
S0182-01
Switch
Control
Current
Control
FB
SMPS
Q1
Q2
Q3
Q4
Input
Voltage
L1
L2
33H
V
driver
V
OUT
22F–470F
Boost SMPS
BUCK/BOOST SWITCH-MODE REGULATOR
SLIS125 – DECEMBER 2006
operating in boost mode and V(driver) is in the crossover window of 5.8 V to 5 V, the output regulation may
contain a higher than normal ripple and only maintain a 3% tolerance. This ripple and tolerance depends on the
loading and improves with a higher loading condition. When the device is operated with low-power mode active
(CLP = low) and high output currents (>50 mA), the buck/boost transitioning can cause a reset signal at the
RESET pin.
In buck mode, the duty cycle of transistor Q1 sets the voltage VOUT. The duty cycle of transistor Q1 varies 10%
to 99% depending on the input voltage, V(driver). If the peak inductor current (measured by Q1) exceeds 450 mA
(typical), Q2 is turned on for this cycle (synchronized rectification). Otherwise, the current recirculates through
Q2 as a free-wheeling diode. The detection for synchronous or asynchronous mode is done cycle-by-cycle.
To avoid a cross-conduction current between Q1 and Q2, an inherent delay is incorporated when switching Q1
off and Q2 on and vice versa.
In buck mode, transistor Q3 is not required and is switched off. Transistor Q4 is switched on to reduce power
dissipation.
The switch timings for transistors Q3 and Q4 are not considered. In buck mode, the logical control of the
transistors does not change.
Figure 2. Buck/Boost Switch Mode Configuration
In boost mode, the duty cycle of transistor Q3 controls the output voltage VOUT. The duty cycle is internally
adjusted 5% to 85% depending on the internally sensed voltage of the output. Synchronized rectification occurs
when V(driver) is below 5 V.
To avoid a discharging of the buffer capacitor, a simultaneous switching on of Q3 and Q4 is not allowed. An
inherent delay is incorporated between Q3 switching off and Q4 switching on and vice versa.
In boost mode, transistor Q2 is not required and remains off. Transistor Q1 is switched on for the duration of the
boost-mode operation (serves as a supply line).
11
相關PDF資料
PDF描述
TPL9201PWP SPECIALTY ANALOG CIRCUIT, PDSO20
TPPM0115DR 0.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO8
TPPM0115D 0.5 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO8
TPS2010APWP 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14
TPS2012Y 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC8
相關代理商/技術參數
參數描述
TPIC74100QPWPRQ1 制造商:Texas Instruments 功能描述:SWITCHING REG BUCK/BOOST 20HTSSOP
TPIC74101EVM 功能描述:電源管理IC開發工具 TPIC74101 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPIC74101-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:BUCK/BOOST SWITCH-MODE REGULATOR
TPIC74101QPWPRQ1 功能描述:直流/直流開關調節器 AC Buck/Boost Switch Mode Reg RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPIC8101 制造商:TI 制造商全稱:Texas Instruments 功能描述:KNOCK SENSOR INTERFACE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*