- 您現在的位置：買賣IC網 > PDF目錄69498 > TPD4122K BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP26 PDF資料下載
參數資料
| 型號： | TPD4122K |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP26 |
| 封裝： | 32 X 13 MM, 2 MM PITCH, PLASTIC, DIP-26 |
| 文件頁數： | 4/25頁 |
| 文件大?。?/td> | 394K |
| 代理商： | TPD4122K |
TPD4122K
2008-08-13
12
Description of Bootstrap Capacitor Charging and Its Capacitance
The IC uses bootstrapping for the power supply for high-side drivers.
The bootstrap capacitor is charged by turning on the low-side IGBT of the same arm (approximately 1/5 of PWM
cycle) while the high-side IGBT controlled by PWM is off. (For example, to drive at 20 kHz, it takes approximately
10
μs per cycle to charge the capacitor.) When the VS voltage exceeds 3.8 V (55 % duty), the low-side IGBT is
continuously in the off state. This is because when the PWM on-duty becomes larger, the arm is short-circuited
while the low-side IGBT is on. Even in this state, because PWM control is being performed on the high-side IGBT,
the regenerative current of the diode flows to the low-side FRD of the same arm, and the bootstrap capacitor is
charged. Note that when the on-duty is 100 %, diode regenerative current does not flow; thus, the bootstrap
capacitor is not charged.
When driving a motor at 100 % duty cycle, take the voltage drop at 100 % duty (see the figure below) into
consideration to determine the capacitance of the bootstrap capacitor.
Capacitance of the bootstrap capacitor
= Current dissipation (max) of the high-side driver × Maximum drive time
/(VCC VF (BSD) + VF (FRD) 13.5) [F]
VF (BSD) : Bootstrap diode forward voltage
VF (FRD) : First recovery diode forward voltage
Consideration must be made for aging and temperature change of the capacitor.
VS Range
IGBT Operation
A
Both high and low-side OFF.
B
Charging range. Low-side IGBT refreshing on the phase the high-side IGBT in PWM.
C
No charging range. High-side at PWM according to the timing chart. Low-side no refreshing.
Safe Operating Area
Note: The above safe operating areas are at Tj
= 135 °C (Figure 1).
1.0
0
450
Peak
winding
current
(A)
Power supply voltage VBB (V)
Figure 1 SOA at Tj
= 135°C
0
Low-side ON
Duty cycle 80 %
C
Triangular wave
Duty cycle 100 % (VS: 5.4 V)
High-side duty ON
PWM reference voltage
Duty cycle 55 % (VS: 3.8 V)
Duty cycle 0 % (VS: 2.1 V)
VVsOFF (VS: 1.3 V)
GND
B
A
相關PDF資料 |
PDF描述 |
|---|---|
| TPD4124K | BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26 |
| TPD7203F | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO24 |
| TPIC0107BDWP | BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20 |
| TPIC0107BDWPR | BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20 |
| TPIC43T02DAR | BRUSHLESS DC MOTOR CONTROLLER, PDSO38 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPD4122K(Q) | 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPD4123AK | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4123AK(Q) | 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPD4123K | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC |
| TPD4123K(Q) | 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。