參數資料
型號： TPD4122K
元件分類： 運動控制電子
英文描述： BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDIP26
封裝： 32 X 13 MM, 2 MM PITCH, PLASTIC, DIP-26
文件頁數： 2/25頁
文件大?。?/td> 394K
代理商： TPD4122K
TPD4122K
2008-08-13
10
External Parts
Typical external parts are shown in the following table.
Part
Typical
Purpose
Remarks
C1, C2, C3
25 V/2.2
μF
Bootstrap capacitor
(Note 1)
R1
0.62
Ω ± 1 % (1 W)
Current detection
(Note 2)
C4
25 V/1000 pF
± 5 %
PWM frequency setup
(Note 3)
R2
27 k
Ω ± 5 %
PWM frequency setup
(Note 3)
C5
25 V/10
μF
Control power supply stability
(Note 4)
C6
25 V/0.1
μF
VREG power supply stability
(Note 4)
R3
5.1 k
Ω
FG pin pull-up resistor
(Note 5)
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. Although the IC
can operate at above the VBS undervoltage level, it is however recommended that the capacitor voltage be
greater than or equal to 13.5 V to keep the power dissipation small. The capacitor is biased by VCC and
must be sufficiently derated accordingly.
Note 2: The following formula shows the detection current: IO = VR ÷ R1 (VR = 0.5 V typ.)
Do not exceed a detection current of 1 A when using the IC.
Note 3: With the combination of C4 and R2 shown in the table, the PWM frequency is around 20 kHz. The IC
intrinsic error factor is around 10 %.
The PWM frequency is broadly expressed by the following formula. (In this case, the stray capacitance of
the printed circuit board needs to be considered.)
fc = 0.65 ÷ { C4 × (R2 + 4.25 kΩ)} [Hz]
R2 creates the reference current of the PWM triangular wave charge/discharge circuit. If R2 is set too small
it exceeds the current capacity of the IC internal circuits and the triangular wave distorts. Set R2 to at least 9
k
Ω.
Note 4: When using the IC, adjustment is required in accordance with the use environment. When mounting, place
as close to the base of the IC leads as possible to improve noise elimination.
Note 5: The FG pin is open drain. If the FG pin is not used, connect to the GND.
Note 6: If noise is detected on the Input signal pin, add a capacitor between inputs.
Note 7: A Hall device should use an indium antimony system.
Handling precautions
(1)
When switching the power supply to the circuit on/off, ensure that VS < VVSOFF (all IGBT outputs
off). At that time, either the VCC or the VBB can be turned on/off first. Note that if the power supply is
switched off as described above, the IC may be destroyed if the current regeneration route to the VBB
power supply is blocked when the VBB line is disconnected by a relay or similar while the motor is
still running.
(2) The IC has a forward/reverse rotation control pin (FR). To change the rotation direction, switch the FR
pin after the motor is stopped in the state that the VS voltage is lower than or equal to 1.1 V. When
the FR pin is switched while the motor is rotating, the following malfunctions may occur.
A shoot-through current may flow between the upper arm and lower arm in the output stage (IGBT)
at that moment when the motor is switched.
An over current may flow into the area where the over current protection circuit cannot detect it.
(3)
The triangular wave oscillator circuit, with externally connected C4 and R2, charges and discharges
minute amounts of current. Therefore, subjecting the IC to noise when mounting it on the board may
distort the triangular wave or cause malfunction. To avoid this, attach external parts to the base of
the IC leads or isolate them from any tracks or wiring which carries large current.
(4)
The PWM of this IC is controlled by the on/off state of the high-side IGBT.
(5)
If a motor is locked where VBB voltage is low and duty is 100 %, it may not be possible to reboot after
the load is released as a result of the high side being ON immediately prior to the motor being locked.
This is because, over time, the bootstrap voltage falls, the high-side voltage decrease protection
operates and the high-side output becomes OFF. In this case, since the level shift pulse necessary to
turn the high side ON cannot be generated, reboot is not possible. A level shift pulse is generated by
either the edge of a Hall sensor output or the edge of an internal PWM signal, but neither edge is
available due to the motor lock and duty 100 % command. In order to reboot after a lock, the high-side
相關PDF資料
PDF描述
TPD4124K BRUSHLESS DC MOTOR CONTROLLER, 3 A, PDIP26
TPD7203F BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO24
TPIC0107BDWP BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20
TPIC0107BDWPR BRUSH DC MOTOR CONTROLLER, 7.5 A, PDSO20
TPIC43T02DAR BRUSHLESS DC MOTOR CONTROLLER, PDSO38
相關代理商/技術參數
參數描述
TPD4122K(Q) 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TPD4123AK 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC
TPD4123AK(Q) 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TPD4123K 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Intelligent Power Device High Voltage Monolithic Silicon Power IC
TPD4123K(Q) 功能描述:馬達/運動/點火控制器和驅動器 Intelligent Power Device, 500V, 1A, BLDC motor drive, DIP26 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*