- 您現在的位置：買賣IC網 > PDF目錄365910 > TPA6017A2PWPR AUDIO AMPLIFIER|DUAL|CMOS|TSSOP|20PIN|PLASTIC PDF資料下載
參數資料
| 型號： | TPA6017A2PWPR |
| 元件分類： | 音頻放大器 |
| 英文描述： | AUDIO AMPLIFIER|DUAL|CMOS|TSSOP|20PIN|PLASTIC |
| 中文描述： | 音頻放大器|雙|的CMOS | TSSOP封裝| 20針|塑料 |
| 文件頁數： | 21/33頁 |
| 文件大?。?/td> | 469K |
| 代理商： | TPA6017A2PWPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
TPA6011A4
SLOS392
–
FEBRUARY 2002
21
www.ti.com
APPLICATION INFORMATION
VOLUME, SEDIFF, and SEMAX operation
Three pins labeled VOLUME, SEDIFF, and SEMAX control the BTL volume when driving speakers and the SE
volume when driving headphones. All of these pins are controlled with a dc voltage, which should not exceed
V
DD
.
When driving speakers in BTL mode, the VOLUME pin is the only pin that controls the gain. Table 1 shows the
gain for the BTL mode. The voltages listed in the table are for V
DD
= 5 V. For a different V
DD
, the values in the
table scale linearly. If V
DD
= 4 V, multiply all the voltages in the table by 4 V/5 V, or 0.8.
The TPA6011A4 allows the user to specify a difference between BTL gain and SE gain. This is desirable to avoid
any listening discomfort when plugging in headphones. When switching to SE mode, the SEDIFF and SEMAX
pins control the singe-ended gain proportional to the gain set by the voltage on the VOLUME pin. When SEDIFF
= 0 V, the difference between the BTL gain and the SE gain is 6 dB. Refer to the section labeled
bridged-tied
load versus single-ended load
for an explanation on why the gain in BTL mode is 2x that of single-ended mode,
or 6dB greater. As the voltage on the SEDIFF terminal is increased, the gain in SE mode decreases. The voltage
on the SEDIFF terminal is subtracted from the voltage on the VOLUME terminal and this value is used to
determine the SE gain.
Some audio systems require that the gain be limited in the single-ended mode to a level that is comfortable for
headphone listening. Most volume control devices only have one terminal for setting the gain. For example, if
the speaker gain is 20 dB, the gain in the headphone channel is fixed at 14 dB. This level of gain could cause
discomfort to listeners and the SEMAX pin allows the designer to limit this discomfort when plugging in
headphones. The SEMAX terminal controls the maximum gain for single-ended mode.
The functionality of the SEDIFF and SEMAX pin are combined to set the SE gain. A block diagram of the
combined functionality is shown in Figure 32. The value obtained from the block diagram for SE_VOLUME is
a dc voltage that can be used in conjunction with Table 2 to determine the SE gain. Again, the voltages listed
in the table are for V
DD
= 5V. The values must be scaled for other values of V
DD
.
Tables 1 and 2 show a range of voltages for each gain step. There is a gap in the voltage between each gain
step. This gap represents the hysteresis about each trip point in the internal comparator. The hysteresis ensures
that the gain control is monotonic and does not oscillate from one gain step to another. If a potentiometer is used
to adjust the voltage on the control terminals, the gain increases as the potentiometer is turned in one direction
and decreases as it is turned back the other direction. The trip point, where the gain actually changes, is different
depending on whether the voltage is increased or decreased as a result of the hysteresis about each trip point.
The gaps in tables 1 and 2 can also be thought of as indeterminate states where the gain could be in the next
higher gain step or the lower gain step depending on the direction the voltage is changing. If using a DAC to
control the volume, set the voltage in the middle of each range to ensure that the desired gain is achieved.
A pictorial representation of the volume control can be found in Figure 33. The graph focuses on three gain steps
with the trip points defined in Table 1 for BTL gain. The dotted line represents the hysteresis about each gain
step.
相關PDF資料 |
PDF描述 |
|---|---|
| TPA6030A4 | 3-W Stereo Audio Power Amplifier with Advanced DC Volume Control |
| TPA6030A4PWP | Slide |
| TPA6100A2 | 50-mW Ultra-Low Voltage Audio Power Amp |
| TPA6110A2DGNR | Switchlocks |
| TPA6111A2DGNR | Rotary Keylock Switch; Key Removal Position:1; Circuitry:SPST; Indexing:90; Contact Current Max:4A; Contact Rating:4A; Leaded Process Compatible:Yes; Mounting Type:Solder Lug; No. of Switch Positions:1; Number of Positions:1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA6017A2PWPRG4 | 功能描述:音頻放大器 Stereo Cost Eff Class-AB RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TPA6019A4PWPR | 制造商:Texas Instruments 功能描述:AUDIO AMP 制造商:TI 功能描述:STEREO BTL 1W AUDIO POWER AMPLIFIER |
| TPA6020A2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.8-W STEREO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER |
| TPA6020A2EVM | 功能描述:音頻 IC 開發工具 TPA6020A2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TPA6020A2RGW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.8-W STEREO FULLY DIFFERENTIAL AUDIO POWER AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。