- 您現在的位置：買賣IC網 > PDF目錄98273 > TPA3125D2N (TEXAS INSTRUMENTS INC) 36 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20 PDF資料下載
參數資料
| 型號： | TPA3125D2N |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 36 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP20 |
| 封裝： | ROHS COMPLIANT, PLASTIC, DIP-20 |
| 文件頁數： | 5/26頁 |
| 文件大?。?/td> | 467K |
| 代理商： | TPA3125D2N |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
APPLICATION INFORMATION
CLASS-D OPERATION
Traditional Class-D Modulation Scheme
+VCC
0V
OutputCurrent
Supply Pumping
Gain Setting via GAIN0 and GAIN1 Inputs
www.ti.com ........................................................................................................................................................................................... SLOS611 – DECEMBER 2008
This section focuses on the class-D operation of the TPA3125D2.
The TPA3125D2 operates in AD mode. There are two main configurations that may be used. For stereo
operation, the TPA3125D2 should be configured in a single-ended (SE) half-bridge amplifier. For mono
applications, TPA3125D2 may be used as a bridge-tied-load (BTL) amplifier. The traditional class-D modulation
scheme, which is used in the TPA3125D2 BTL configuration, has a differential output where each output is 180
degrees out of phase and changes from ground to the supply voltage, VCC. Therefore, the differential prefiltered
output
varies
between
positive
and
negative
VCC,
where
filtered
50%
duty
cycle
yields
0 V across the load. The class-D modulation scheme with voltage and current waveforms is shown in Figure 26.
Figure 26. Class-D Modulation for TPA3125D2 SE Configuration
One issue encountered in single-ended (SE) class-D amplifier designs is supply pumping. Power-supply pumping
is a rise in the local supply voltage due to energy being driven back to the supply by operation of the class-D
amplifier. This phenomenon is most evident at low audio frequencies and when both channels are operating at
the same frequency and phase. At low levels, power-supply pumping results in distortion in the audio output due
to fluctuations in supply voltage. At higher levels, pumping can cause the overvoltage protection to operate,
which temporarily shuts down the audio output.
Several things can be done to relieve power-supply pumping. The lowest impact is to operate the two inputs out
of phase 180° and reverse the speaker connections. Because most audio is highly correlated, this causes the
supply pumping to be out of phase and not as severe. If this is not enough, the amount of bulk capacitance on
the supply must be increased. Also, improvement is realized by hooking other supplies to this node, thereby,
sinking some of the excess current. Power-supply pumping should be tested by operating the amplifier at low
frequencies and high output levels.
The gain of the TPA3125D2 is set by two input terminals, GAIN0 and GAIN1.
The gains listed in Table 2 are realized by changing the taps on the input resistors and feedback resistors inside
the amplifier. This causes the input impedance (ZI) to be dependent on the gain setting. The actual gain settings
are controlled by ratios of resistors, so the gain variation from part-to-part is small. However, the input impedance
from part-to-part at the same gain may shift by ±20% due to shifts in the actual resistance of the input resistors.
For design purposes, the input network (discussed in the next section) should be designed assuming an input
impedance of 8 k
, which is the absolute minimum input impedance of the TPA3125D2. At the higher gain
settings, the input impedance could increase as high as 72 k
.
Copyright 2008, Texas Instruments Incorporated
13
Product Folder Link(s): TPA3125D2
相關PDF資料 |
PDF描述 |
|---|---|
| TPA3200D1DCP | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPR | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPRG4 | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA3200D1DCPG4 | 12.8 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO44 |
| TPA321DGNR | 0.7 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPA3128D2DAP | 功能描述:IC AUDIO AMP CLASS D 32HTSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:46 |
| TPA3128D2DAPR | 功能描述:IC AUDIO AMP CLASS D 32-HTSSOP 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C（TA） 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬）裸露焊盤 標準包裝:1 |
| TPA3128D2EVM | 功能描述:TPA3128D2EVM 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPA3129D2DAP | 功能描述:IC AUDIO AMP CLASS D 32HTSSOP 制造商:texas instruments 系列:- 包裝:管件 零件狀態:在售 類型:D 類 輸出類型:2 通道（立體聲） 不同負載時的最大輸出功率 x 通道數:30W x 2 @ 8 歐姆 電壓 - 電源:4.5 V ~ 26 V 特性:短路和熱保護 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 供應商器件封裝:32-HTSSOP 封裝/外殼:32-TSSOP（0.240"，6.10mm 寬） 標準包裝:46 |
| TPA3130D2 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:15W,30W,50W Filter-Free Class-D Stereo Amplifier Family with AM Avoidance |
發布緊急采購，3分鐘左右您將得到回復。