參數資料
型號： TMS320C40-50
元件分類： 數字信號處理
英文描述： Digital Signal Processors
中文描述： 數字信號處理器
文件頁數： 59/132頁
文件大?。?/td> 1707K
代理商： TMS320C40-50
SPRS145G
–
JULY 2000
–
REVISED FEBRUARY 2002
59
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
–
1443
SPI slave mode operation in LF2403A
The LF2403A device does not have the SPISTE/IOPC5 pin. (This function is available as an internal signal only.)
The following must be done to put the LF2403A SPI in slave mode:
1.
Configure SPISTE/IOPC5 signal for GPIO mode by clearing the MCRB.5 bit.
2.
Configure SPISTE/IOPC5 signal as an output (by writing a 1 to bit 13 of PCDATDIR) and drive it low (by
writing a 0 to bit 5 of PCDATDIR). Note that SPISTE/IOPC5 should not be driven low until after the SPI is
configured and taken out of reset.
NOTE: The slave SPISTE/IOPC5 signal must not be driven low until after the master
and
slave SPI modules
are configured and taken out of reset. The initialization sequence is as follows:
a.
The master SPI is configured first and taken out of reset. This ensures that the master SPICLK is
initialized to its appropriate level (high or low, depending on the polarity bit) first, before the slave SPI
starts accepting clock pulses.
b.
The slave SPI is configured and taken out of reset.
c.
The GPIO/SPI pins of the slave is then configured for SPI operation and the SPISTE/IOPC5 signal is
driven low. This is done
after
ensuring the correct level of the master SPICLK signal. One method of
doing this would be to read the level of the SPICLK pin through the PCDATDIR register and then
deciding on the appropriate course of action.
d.
SPI transmission may commence now. Transmission of data should not be attempted until both master
and slave are configured and the slave SPISTE/IOPC5 signal is driven low.
相關PDF資料
PDF描述
TMS320C40-60 Digital Signal Processors
TMS320C40TABL40 32-Bit Digital Signal Processor
TMS320C40TABL50 32-Bit Digital Signal Processor
TMS320C40TABL60 32-Bit Digital Signal Processor
TMS320C44-50 Digital Signal Processors
相關代理商/技術參數
參數描述
TMS320C40-60 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Signal Processors
TMS320C40GFL40 功能描述:數字信號處理器和控制器 - DSP, DSC Digital Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C40GFL50 功能描述:數字信號處理器和控制器 - DSP, DSC Digital Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C40GFL60 功能描述:數字信號處理器和控制器 - DSP, DSC Digital Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C40TABL40 制造商:未知廠家 制造商全稱:未知廠家 功能描述:32-Bit Digital Signal Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*