- 您現在的位置：買賣IC網 > PDF目錄368665 > TMS28F512A-15C4FME (Texas Instruments, Inc.) GT 37C 37#16 SKT PLUG PDF資料下載
參數資料
| 型號： | TMS28F512A-15C4FME |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | GT 37C 37#16 SKT PLUG |
| 中文描述： | 65536 8位快閃記憶體 |
| 文件頁數： | 7/21頁 |
| 文件大?。?/td> | 311K |
| 代理商： | TMS28F512A-15C4FME |
TMS28F512A
65536 BY 8-BIT
FLASH MEMORY
SMJS514C – FEBRUARY 1994 – REVISED AUGUST 1997
7
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
set-up-erase/erase commands
The erase algorithm initiates with E = V
IL
, W = V
IL
, G = V
IH
, V
PP
= V
PPH
, and V
CC
= 5 V. To enter the erase mode,
write the set-up-erase command, 20h, into the command register. After the TMS28F512A is in the erase mode,
writing a second erase command, 20h, into the command register invokes the erase operation. The erase
operation begins on the rising edge of W and ends on the rising edge of the next W. The erase operation requires
10 ms to complete before the erase-verify command, A0h, can be loaded.
Maximum erase timing is controlled by the internal stop timer. When the stop timer terminates the erase
operation, the device enters an inactive state and remains inactive until another command is received.
erase-verify command
All bytes must be verified following an erase operation. After the erase operation is complete, an erased byte
can be verified by writing the erase-verify command, A0h, into the command register. This command causes
the device to exit the erase mode on the rising edge of W. The address of the byte to be verified is latched on
the falling edge of W. The erase-verify operation remains enabled until a command is written to the command
register.
To determine whether or not all the bytes have been erased, the TMS28F512A applies a margin voltage to each
byte. If FFh is read from the byte, all bits in the designated byte have been erased. The erase-verify operation
continues until all of the bytes have been verified. If FFh is not read from a byte, an additional erase operation
needs to be executed. Figure 1 shows the combination of commands and bus operations for electrically erasing
the TMS28F512A.
set-up-program/program commands
The programming algorithm initiates with E = V
IL
, W = V
IL
, G = V
IH
, V
PP
= V
PPH
, and V
CC
= 5 V. To enter the
programming mode, write the set-up-program command, 40h, into the command register. The programming
operation is invoked by the next write-enable pulse. Addresses are latched internally on the falling edge of W,
and data is latched internally on the rising edge of W. The programming operation begins on the rising edge
of W and ends on the rising edge of the next W pulse. The program operation requires 10
μ
s for completion
before the program-verify command, C0h, can be loaded.
Maximum program timing is controlled by the internal stop timer. When the stop timer terminates the program
operation, the device enters an inactive state and remains inactive until a command is received.
program-verify command
The TMS28F512A can be programmed sequentially or randomly because it is programmed one byte at a time.
Each byte must be verified after it is programmed. The program-verify operation prepares the device to verify
the most recently programmed byte. To invoke the program-verify operation, C0h must be written into the
command register. The program-verify operation ends on the rising edge of W.
While verifying a byte, the TMS28F512A applies an internal margin voltage to the designated byte. If the true
data and programmed data match, programming continues to the next designated byte location; otherwise, the
byte must be reprogrammed. Figure 1 shows how commands and bus operations are combined for byte
programming.
reset command
To reset the TMS28F512A after set-up-erase command or set-up-program command operations without
changing the contents in memory, write FFh into the command register two consecutive times. After executing
the reset command, the device defaults to the read mode.
相關PDF資料 |
PDF描述 |
|---|---|
| TMS28F512A-15C4FMQ | 65536 BY 8-BIT FLASH MEMORY |
| TMS28F512A-17 | 65536 BY 8-BIT FLASH MEMORY |
| TMS28F512A-17C3FME | GT 7C 7#16S PIN PLUG |
| TMS28F512A-17C3FML | GT 7C 7#16S PIN PLUG |
| TMS28F512A-17C3FMQ | GT 14C 12#8 2#16 SKT PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMS29F040-12C5FML | 制造商:Texas Instruments 功能描述: |
| TMS29F04090C5FML | 制造商:TI 功能描述:* |
| TMS29F040-90C5FML | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TMS29F04090C5FMLR | 制造商:TI 功能描述:* |
| TMS29F81606FML | 制造商:TI 功能描述:* |
發布緊急采購，3分鐘左右您將得到回復。