參數資料
型號: TMP512AIRSAT
廠商: TEXAS INSTRUMENTS INC
元件分類: 模擬信號調理
英文描述: SPECIALTY ANALOG CIRCUIT, PQCC16
封裝: GREEN, PLASTIC, QFN-16
文件頁數: 32/61頁
文件大?。?/td> 1758K
代理商: TMP512AIRSAT
SBOS491A
– JUNE 2010 – REVISED MAY 2011
Bit Descriptions (continued)
RM3:
Remote Temperature 3 Over-Limit (TMP513 only)
Bit 7
This bit is set to '1' when the result in the Remote Temperature Result 3 Register (0Bh) exceeds the level set in the
Remote Temperature Limit 3 Register (14h) plus half of the temperature hysteresis. It sets also if during conversion
of remote channel 3 an open diode condition was detected. It clears in transparent mode when the result in the
Remote Temperature Result 3Register (0Bh) is below the level set in the Remote Temperature Limit 3 Register
(14h) minus half of the temperature hysteresis and the last conversion of channel 3 was done without open-diode
detection.
CVR:
Conversion Ready
Bit 6
The Conversion Ready line is provided to help coordinate one-shot conversions for shunt voltage, bus voltage,
current and power measurements. The Conversion bit is set after all conversions, averaging, and multiplication
events are complete. Conversion Ready clears under the following conditions:
1.
Writing to the One-Shot bit in Configuration Register 1.
2.
Reading the Status Register.
CRT:
Conversion Ready Temperature
Bit 5
The Conversion Ready Temperature line is provided to help coordinate one-shot conversions for local and remote
temperature measurements. The Conversion bit is set after all enabled channels complete the respective
conversions. Conversion Ready Temperature clears under the following conditions:
1.
Writing to the One-Shot bit in Configuration Register 1.
2.
Reading the Status Register.
PVLD:
Power Valid Error
Bit 4
In latch mode, this bit is set to '1' when the brown-out detect fires during a conversion. The flag sets to '1' at the
conversion end. It clears by reading the Status Register.
SMBA:
SMBus Alert
Bit 3
This bit is set when the Alert pin is active. When in latch mode, it clears only on reading the Status Register,
disabling the SMBus Alert function, or using SMBus Alert Response. In transparent mode, it clears when the
triggering condition is not present.
OVF:
Math Overflow
Bit 2
This bit is set to '1' if an arithmetic operation resulted in an overflow error. It indicates that current and power data
may be meaningless. It does not set the Alert pin.
38
Copyright
2010–2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
TMP815PWR AC MOTOR CONTROLLER, PDSO16
TN5D51 5 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, SFM5
TN7D51 7 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, PZFM5
TN7D51 7 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, PZFM5
TNY264PG 0.4 A SWITCHING REGULATOR, 140 kHz SWITCHING FREQ-MAX, PDIP7
相關代理商/技術參數
參數描述
TMP513 制造商:TI 制造商全稱:Texas Instruments 功能描述:Temperature and Power Supply System Monitors
TMP513AID 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitoring Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIDR 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitoring Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIRSAR 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitor Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIRSAT 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitor Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor