參數資料
型號： TMP512AIRSAT
廠商： TEXAS INSTRUMENTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PQCC16
封裝： GREEN, PLASTIC, QFN-16
文件頁數： 17/61頁
文件大?。?/td> 1758K
代理商： TMP512AIRSAT
SBOS491A
– JUNE 2010 – REVISED MAY 2011
In applications that do not have large energy storage
not generate an Acknowledge and continues to hold
electrolytics on one or both sides of the shunt, an
the ALERT line low until the interrupt is cleared.
input
overstress
condition
may
result
from
an
Successful completion of the read alert response
excessive dV/dt of the voltage applied to the input. A
protocol clears the SMBus ALERT pin, provided that
hard physical short is the most likely cause of this
the condition causing the alert no longer exists. The
event, particularly in applications with no large
SMBus Alert flag is cleared separately by either
electrolytics present. This problem occurs because an
reading the Status Register or by disabling the
excessive dV/dt can activate the ESD protection in
SMBus Alert function.
the TMP512/13 in systems where large currents are
The Status Register flags indicate which (if any) of
available. Testing has demonstrated that the addition
the watchdogs have been activated. After power-on
of 10
resistors in series with each input of the
reset (POR), the normal state of all flag bits is '0',
TMP512/13 sufficiently protects the inputs against
assuming that no alarm conditions exist.
dV/dt failure up to the 26V rating of the TMP512/13.
These
resistors
have
no
significant
effect
on
EXTERNAL CIRCUITRY FOR ADDITIONAL
accuracy.
VBUS INPUT
SMBus ALERT RESPONSE
The TMP512/13 GPIO can be used to control an
external circuit to switch the VBUS measurement to an
The SMBus alert response functions only when the
alternate location. Switching is most often done to
Alert pin is active and in latch mode (03h, bit 0 = 1);
perform bus voltage measurements on the opposite
see Figure 26. The ALERT interrupt output signal is
side of a MOSFET switch in series with the shunt
latched and can be cleared only by either reading the
resistor.
Status Register or by successfully responding to an
alert response address. If the fault is still present, the
Consideration must be given to the typical 20
μA input
ALERT pin re-asserts. Asserting the ALERT pin does
current of each TMP512/13 input, along with the
not halt automatic conversions that are already in
320k
impedance present at the VIN– input where the
progress. The ALERT output pin is open-drain,
bus voltage is measured. These effects can create
allowing multiple devices to share a common interrupt
errors
through
the
resistance
of
any
external
line.
switching method used. The easiest way to avoid
these errors is by reducing this resistance to a
The
TMP512/13
respond
to
the
SMBus
alert
minimum; select switching MOSFETs with the lowest
response address, an interrupt pointer return-address
possible RDS(on) values.
feature. The SMBus alert response interrupt pointer
provides quick fault identification for simple slave
The circuit shown in Figure 31 uses MOSFET pairs to
devices. When an ALERT occurs, the master can
reduce package count. Back-to-back MOSFETs must
broadcast the alert response slave address (0001
be used in each leg because of the built-in back
100). Following this alert response, any slave devices
diodes from source-to-drain. In this circuit, the normal
that generated interrupts identify themselves by
connection for VIN– is at the shunt, with the optional
putting the respective addresses on the bus.
voltage measurement at the output of the control
FET.
The alert response can activate several different
slave devices simultaneously, similar to the two-wire
General Call. If more than one slave attempts to
respond, bus arbitration rules apply; the device with
the lower address code wins. The losing device does
24
Copyright
2010–2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
TMP815PWR AC MOTOR CONTROLLER, PDSO16
TN5D51 5 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, SFM5
TN7D51 7 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, PZFM5
TN7D51 7 A SWITCHING REGULATOR, 180 kHz SWITCHING FREQ-MAX, PZFM5
TNY264PG 0.4 A SWITCHING REGULATOR, 140 kHz SWITCHING FREQ-MAX, PDIP7
相關代理商/技術參數
參數描述
TMP513 制造商:TI 制造商全稱:Texas Instruments 功能描述:Temperature and Power Supply System Monitors
TMP513AID 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitoring Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIDR 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitoring Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIRSAR 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitor Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
TMP513AIRSAT 功能描述:板上安裝溫度傳感器 All-In-One Thermal & Pwr Monitor Sol RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*