- 您現在的位置：買賣IC網 > Datasheet目錄47 > TMP401AIDGKTG4 (Texas Instruments)IC TEMP SENSOR DGTL OUT 8-MSOP Datasheet資料下載
參數資料
| 型號： | TMP401AIDGKTG4 |
| 廠商： | Texas Instruments |
| 文件頁數： | 21/28頁 |
| 文件大?。?/td> | 881K |
| 描述： | IC TEMP SENSOR DGTL OUT 8-MSOP |
| 標準包裝： | 250 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C |
| 精確度： | ±3°C 本地（最大），±5°C 遠程（最大） |
| 拓?fù)洌?/td> | ADC，比較器，寄存器庫 |
| 輸出類型： | 2 線 SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TMP401
SBOS371A AUGUST 2006 REVISED OCTOBER 2007
www.ti.com
21
LAYOUT CONSIDERATIONS
Remote temperature sensing on the TMP401 measures
very small voltages using very small currents; therefore,
noise at the IC inputs must be minimized. Most
applications using the TMP401 will have high digital
content, with several clocks and logic level transitions
creating a noisy environment. Layout should adhere to the
following guidelines:
1. Place the TMP401 as close to the remote junction
sensor as possible.
2. Route the D+ and D traces next to each other and
shield them from adjacent signals through the use
of ground guard traces, as shown in Figure 18. If a
multilayer PCB is used, bury these traces between
ground or V
DD
planes to shield them from extrinsic
noise sources. 5 mil PCB traces are recommended.
3. Minimize additional thermocouple junctions caused
by copper-to-solder connections. If these junctions
are used, make the same number and approximate
locations of copper-to-solder connections in both
the D+ and D connections to cancel any
thermocouple effects.
4. Use a 0.1礔 local bypass capacitor directly
between the V+ and GND of the TMP401, as shown
in Figure 19. Minimize filter capacitance between
D+ and D to 1000pF or less for optimum
measurement performance. This capacitance
includes any cable capacitance between the
remote temperature sensor and TMP401.
5. If the connection between the remote temperature
sensor and the TMP401 is between 8 inches and 12
feet, use a twisted-wire pair connection. Beyond
this distance (up to 100ft), use a twisted, shielded
pair with the shield grounded as close to the
TMP401 as possible. Leave the remote sensor
connection end of the shield wire open to avoid
ground loops and 60Hz pickup.
GND
(1)
D+
(1)
D
(1)
GND
(1)
NOTE: (1) 5 mil traces with 5 mil spacing.
Ground or V+ layer
on bottom and/or
top, if possible.
Figure 18. Example Signal Traces
1
2
3
4
8
7
6
5
TMP401
0.1礔 Capacitor
PCB Via
PCB Via
V+
GND
Figure 19. Suggested Bypass Capacitor
Placement
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2346PWRG4 | IC HOT SWAP POWER MGR 24-TSSOP |
| TPS24711DGSR | IC CTRLR HOT SWAP 2.5-18V 10MSOP |
| TPS2491DGSG4 | IC POS HV HOT-SWAP CTRLR 10-MSOP |
| W83772G | IC H/W MONITOR 8-TSSOP |
| W83L786G | IC H/W MONITOR 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMP411 | 制造商:BB 制造商全稱:BB 功能描述:【1C Remote and Local TEMPERATURE SENSOR with N-Factor and Series Resistance Correction |
| TMP411_07 | 制造商:BB 制造商全稱:BB 功能描述:【1∑C Remote and Local TEMPERATURE SENSOR with N-Factor and Series Resistance Correction |
| TMP411_13 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:?±1?°C Remote and Local TEMPERATURE SENSOR with N-Factor and Series Resistance Correction |
| TMP411A | 制造商:BB 制造商全稱:BB 功能描述:【1∑C Remote and Local TEMPERATURE SENSOR with N-Factor and Series Resistance Correction |
| TMP411AD | 功能描述:板上安裝溫度傳感器 +/-1degC Remote and Local Temp SENSOR RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。