- 您現在的位置：買賣IC網 > PDF目錄69494 > TLE8242 (INFINEON TECHNOLOGIES AG) SPECIALTY ANALOG CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TLE8242 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 封裝： | GREEN, PLASTIC, LQFP-64 |
| 文件頁數： | 22/77頁 |
| 文件大?。?/td> | 1580K |
| 代理商： | TLE8242 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
Data Sheet
29
Rev. 1.0, 2009-02-25
TLE8242
Functional Description and Electrical Characteristics
5.6
Current Feedback Registers
The average current over each PWM cycle is measured resulting in a 13 bit value. The summation of the 13 bit
values for all PWM periods in a dither period can be read by accessing SPI message #13. Also, the 11 MSb’s of
the minimum and maximum 13 bit values within a dither period can be read by accessing SPI message #12.
Average Current Over Dither Period
When the SPI message #13 is read or written, the 13 bit average current value for each PWM cycle within the
dither period is summed beginning with the positive going zero crossing of the dither waveform. The resulting 20
bit value represents the average current over the dither cycle as shown in equation:
If dither is disabled (Dither Steps = 0 or Dither Amplitude = 0), then the Average Current Feedback value will be
updated every PWM period and will be the same as the 13 bit current feedback value used in the PI controller.(1)
The SPI message #13 includes a VALID bit that indicates whether the average current measurement has
completed since the last register access. When the register is accessed, the VALID bit is cleared. The VALID bit
is set again when the summation is completed and new data has been stored in the register.
The summation process runs continuously on the last selected channel. So if the same channel is repeatedly
selected, new data is always available within one dither period after the SPI register is accessed.
If the selected channel is different than the previously selected channel, the summation process does not begin
until the beginning of the next dither period. So, new data may not be available until two dither cycles have
completed.
The channel selection for the Average Dither Current Feedback Message message will also select the channel for
the Minimum and Maximum Current Over Dither Period function.
Minimum and Maximum Current Over Dither Period
When the SPI message #12 is read or written, the 13 bit average current value for each PWM cycle within the
dither period is monitored beginning with the positive going zero crossing of the dither waveform. The most
significant 11 bits of the minimum and the maximum average current values are stored.
If dither is disabled (Dither Steps = 0 or Dither Amplitude = 0), then the Minimum and Maximum values will be
updated every PWM period and will be the 11 Msb’s of the 13 bit current feedback value used in the PI controller.
The SPI message #12 includes a VALID bit that indicates whether a dither period has completed since the last
register access. When the register is accessed, the VALID bit is cleared. The VALID bit is set again when the dither
period is completed and new data has been stored in the minimum and maximum registers.
The minimum and maximum detection process runs continuously on the last selected channel. So, if the same
channel is repeatedly selected, new data is always available within one dither period after the SPI register is
accessed.
If the selected channel is different than the previously selected channel, the detection process does not begin until
the beginning of the next dither period. So, new data may not be available until two dither cycles have completed.
The channel selection for the Minimum and Maximum Current Over Dither Period message will also select the
channel for the Average Dither Current Feedback function.
[]
]
Ohm
[
]
mV
[
320
2
mA
Feedback
Current
Dither
15
Rsense
Steps
Dither
Current
Avg Dither
=
相關PDF資料 |
PDF描述 |
|---|---|
| TLE8386EL | 0.09 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO14 |
| TLI4946-2L | MAGNETIC SENSOR, PSIP3 |
| TLI4946K | MAGNETIC SENSOR, PDSO3 |
| TLV431AIDBVR | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO5 |
| TLV431ACDBVT | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE8242-2 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8 Channel Fixed Frequency Constant Current Control With Current Profile Detection |
| TLE82452SAALLA1 | 制造商:Infineon Technologies AG 功能描述:TRANSMISSION_IC - Rail/Tube |
| TLE82452SAAUMA1 | 制造商:Infineon Technologies AG 功能描述:TRANSMISSION_IC - Tape and Reel |
| TLE8250G | 功能描述:CAN 接口集成電路 High Speed CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| TLE8250GVIO | 功能描述:CAN 接口集成電路 High Speed CAN Transceiver RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。