- 您現在的位置：買賣IC網 > PDF目錄373651 > TLC154 (Electronic Theatre Controls, Inc.) EPROM/ROM-Based 8-Bit Microcontroller Series PDF資料下載
參數資料
| 型號： | TLC154 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | EPROM/ROM-Based 8-Bit Microcontroller Series |
| 中文描述： | 存儲器/基于ROM的8位微控制器系列 |
| 文件頁數： | 20/50頁 |
| 文件大?。?/td> | 552K |
| 代理商： | TLC154 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
2.4.3 Port B Input Change Interrupt
An input change on IOB<7:0> set flag bit PBIF (INTFLAG<1>). This interrupt can be disabled by clearing PBIE bit
(INTEN<1>).
Before the port B input change interrupt is enabled, reading PORTB (any instruction accessed to PORTB, including
read/write instructions) is necessary. Any pin which corresponding
WUBn bit (WUCON<7:0>) is cleared to “0” or
configured as output or IOB0 pin configured as INT pin will be excluded from this function.
The port B input change interrupt also can wake-up the system from SLEEP condition, if bit PBIE was set before
going to SLEEP. And GIE bit also decides whether or not the processor branches to the interrupt vector following
wake-up. If GIE bit was set, the program will execute interrupt service routine after wake-up; or if GIE bit was cleared,
the program will execute next PC after wake-up.
2.5 Power-down Mode (SLEEP)
Power-down mode is entered by executing a SLEEP instruction.
When SLEEP instruction is executed, the
PD
bit (STATUS<3>) is cleared, the
TO
bit is set,
the watchdog timer will
be cleared and keeps running, and the oscillator driver is turned off.
All I/O pins maintain the status they had before the SLEEP instruction was executed.
2.5.1 Wake-up from SLEEP Mode
The device can wake-up from SLEEP mode through one of the following events:
1. RSTB reset.
2. WDT time-out reset (if enabled).
3. Interrupt from RB0/INT pin, or PORTB change interrupt.
External RSTB reset and WDT time-out reset will cause a device reset. The
PD
and
TO
bits can be used to
determine the cause of device reset. The
PD
bit is set on power-up and is cleared when SLEEP instruction is
executed. The
TO
bit is cleared if a WDT time-out occurred.
For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set. Wake-up
is regardless of the GIE bit. If GIE bit is cleared, the device will continue execution at the instruction after the SLEEP
instruction. If the GIE bit is set, the device will branch to the interrupt address (008h).
The system wake-up delay time is 18ms plus 128 oscillator cycle time.
2.6 Reset
TLC156 devices may be RESET in one of the following ways:
1. Power-on Reset (POR)
2. Brown-out Reset (BOR)
3. RSTB Pin Reset
4. WDT time-out Reset
Some registers are not affected in any RESET condition. Their status is unknown on Power-on Reset and
unchanged in any other RESET. Most other registers are reset to a “reset state” on Power-on Reset, RSTB or WDT
Reset.
A Power-on RESET pulse is generated on-chip when Vdd rise is detected. To use this feature, the user merely ties
the RSTB pin to Vdd.
On-chip Low Voltage Detector (LVD) places the device into reset when Vdd is below a fixed voltage. This ensures
that the device does not continue program execution outside the valid operation Vdd range. Brown-out RESET is
typically used in AC line or heavy loads switched applications.
A RSTB or WDT Wake-up from SLEEP also results in a device RESET, and not a continuation of operation before
SLEEP.
The
TO
and
PD
bits (STATUS<4:3>) are set or cleared depending on the different reset conditions.
TLC
TLC156
Rev0.95 Nov 20, 2003
P.2/TLC156
相關PDF資料 |
PDF描述 |
|---|---|
| TLC154D | EPROM/ROM-Based 8-Bit Microcontroller Series |
| TLC154EP | EPROM/ROM-Based 8-Bit Microcontroller Series |
| TLC154ER | EPROM/ROM-Based 8-Bit Microcontroller Series |
| TLC154P | EPROM/ROM-Based 8-Bit Microcontroller Series |
| TLC154R | EPROM/ROM-Based 8-Bit Microcontroller Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLC1541 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:10-BIT ANALOG-TO-DIGITAL CONVERTER WITH SERIAL CONTROL AND 11 INPUTS |
| TLC1541CDW | 功能描述:模數轉換器 - ADC 10bit A/D w/Ser In RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541CDWG4 | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541CDWR | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLC1541CDWRG4 | 功能描述:模數轉換器 - ADC 10-Bit 32 kSPS Serial Out RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。